One-component pre-blended thixotropic mortar with controlled shrinkage for anchoring, by injection, of tie rods and bolts in all types of grounds. Use Stabilcem T for anchoring tie rods of any length…
One-component pre-blended thixotropic mortar with controlled shrinkage for…
Alkali-resistant glass fibre mesh (in compliance with the ETAG 004 guide) for reinforcing protective waterproofing layers, anti-fracture membranes and thermal insulation systems.
Alkali-resistant glass fibre mesh (in compliance with the ETAG 004 guide) for…
One-component, ultra-fluid polyurethane resin applied by injection for waterproofing structures and ground and rocks subject to intense percolating water. The reaction time may be regulated.…
One-component, ultra-fluid polyurethane resin applied by injection for…
Mapecrete LI Hardener penetrates into the pores of the substrate and reacts with the free lime that is normally produced during the hydration phase of the cement. This reaction produces highly…
Mapecrete LI Hardener penetrates into the pores of the substrate and reacts…
One-component, solvent-free primer for polyurethane sealants, for use on absorbent and non-absorbent surfaces. TECHNICAL DATA: Consistency: liquid. Colour: transparent. Inflammable: no. Application…
One-component, solvent-free primer for polyurethane sealants, for use on…
Lime-cement skimming mortar with a fine-textured, natural finish for render and concrete. TECHNICAL DATA: Maximum dimension of aggregate: 0.4 mm. Mixing ratio: 100 parts of PLANITOP 530 with 24-27…
Lime-cement skimming mortar with a fine-textured, natural finish for render and…
Lime-cement skimming mortar with an ultra-fine-textured finish for render. TECHNICAL DATA: Maximum dimension of aggregate: < 0.1 mm. Mixing ratio: 100 parts of PLANITOP 560 with 39-43 parts of water.…
Lime-cement skimming mortar with an ultra-fine-textured finish for render.…
Bulk powder or liquid water-repellent for cementitious mortar. TECHNICAL DATA: Consistency: powder or liquid. Pot life of mix: approximately 1 hour. Storage: 12 months. Consumption: – IDROSILEX…
Bulk powder or liquid water-repellent for cementitious mortar. TECHNICAL DATA:…
Planicrete SP is a greenish white, multipurpose synthetic-rubber latex to be mixed before use with Portland cement and aggregate (having correct granulometry) to obtain mortars with extremely high…
Planicrete SP is a greenish white, multipurpose synthetic-rubber latex to be…
Hydro-oil repellent and anti-stain treatment for concrete, natural stone and cementitious surfaces made from modified organic polymers in water solution. TECHNICAL DATA: Application temperature…
Hydro-oil repellent and anti-stain treatment for concrete, natural stone and…
Especially fine non-slip cementitious adhesive for absorbent ceramic tiles WHERE TO USE For interior fixing of ceramic tiles and ceramic mosaics, double-fired or single-fired on floors and walls on…
Especially fine non-slip cementitious adhesive for absorbent ceramic tiles…
Pultruded carbon fibre plate with a protective plastic film on both faces. TECHNICAL DATA: Modulus of elasticity: 170 - 200 - 250 GPa. Fibre content: 68% - 68% - 65%. Thickness: 1.4 mm. Width: 50,…
Pultruded carbon fibre plate with a protective plastic film on both faces.…
Paintable polyurethane sealant with a low modulus of elasticity for movements up to 25%. TECHNICAL DATA: Movement in service: 25%. Modulus of elasticity at 100% elongation: 0.24 N/mm². Shore A…
Paintable polyurethane sealant with a low modulus of elasticity for movements…
Closed-cell, extruded foam polyethylene cord used as a support for elastomer sealants to gauge the correct size of flexible joints. Supplied in rolls in various lengths according to the diameter of…
Closed-cell, extruded foam polyethylene cord used as a support for elastomer…
Solvent gel for removing adhesive and paint. TECHNICAL DATA: Consistency: gel. Colour: transparent. Inflammable: yes. Application temperature range: from +10°C to +35°C. Removal time: – adhesives in…
Solvent gel for removing adhesive and paint. TECHNICAL DATA: Consistency: gel.…
Three-component epoxy mortar with high chemical resistance for grouting ceramic tiles (minimum width of joint 5 mm). Technical data: Pot life of mix: 20 minutes. Set to light foot traffic: approx. 6…
Three-component epoxy mortar with high chemical resistance for grouting ceramic…
