THE IMPORTANCE OF BUTTERING TILES
What are the other main reasons that make the amount of contact surface between the adhesive and the tiles so important? First and foremost, having no air pockets in the layer of adhesive can prevent tiles breaking if they are subjected to concentrated loads, especially in the case of thin tiles that have a lower level of flexural strength compared with traditional thicker tiles (N.B. according to aforementioned UNI 11493-1 standards, thin tiles/slabs are those with a maximum thickness of 5 mm). A full layer of adhesive (which means a layer with no air pockets) guarantees that loads are distributed evenly throughout the support layers which, if compliant with the specifications of the relative standards, have the capacity to withstand such loads.
Buttering tiles correctly is also significant when they are installed on external surfaces or on surfaces constantly in contact with water. The buttering of the tiles with the adhesive is inversely proportional to the amount of air pockets; the fewer air pockets in the surface, the lower the amount of space where standing water could collect and lead to problems/risks connected with freeze-thaw cycles (in the case of external tiling), leaching and aggression to the layer of adhesive (if we consider that water is also a vehicle for transporting substances that could potentially damage the adhesive used to install the tiles).
For all these reasons, it is clear that, the higher the percentage of the rear side of the tile/slab covered by the adhesive, the better the end result. A full installation bed (100% buttering), on the other hand, is a very important aspect when installing large-size tiles (according to the above-mentioned standard, large size tiles are those with one side measuring more than 60 cm) and/or thin tiles, and when installing tiles on external surfaces (including on facades) or on surfaces in constant contact with water.
In order to achieve full installation bed, the double-buttering method is prescribed to install tiles, that is, applying the adhesive on both the substrate and on the rear side of the tiles with a suitable notched trowel.
The double-buttering method is recommended when the compactness of the layer of adhesive and the absence of air pockets under the tiles – that is, to have a “full” installation bed – are essential requirements, which is generally difficult to achieve using the conventional single-buttering method, that is, by applying the adhesive only on the substrate.
It is important to point out that the creation of a “full” installation bed can also be achieved, or made easier, by prescribing the use of adhesives with high wettability: adhesives specially formulated to increase their buttering capacity and, as a result, increase the amount of contact area, under the same conditions, compared with traditional adhesives. This result is obtained by developing adhesives with modified rheology, that is, adhesives that are distributed over the rear side of the tiles more easily during application and then when the tiles are tapped into position after being installed, without affecting either their rib stability or the thickness of the layer of adhesive, including when installing heavy tiles.
The key aspects to take into consideration when prescribing the double-buttering method or, more in general, when the objective is to create a “full” installation bed, are the following:
- the type and size of the tiles (length of the sides, thickness, the profile of the rear side): a full bed needs to be prescribed for large size tiles, tiles with uneven rear side and for thin tiles;
- characteristics of the installation surface (a full bed should be prescribed, for example, when installing tiles on facades);
- high mechanical loads and stresses acting on the tiles (areas subjected to heavy and/or intense traffic);
- high thermal-hygrometric loads and stresses acting on the tiles;
- particular durability and safety requirements;
- heated substrates: heat is transmitted more efficiently through a full bed.
THE CORRECT APPROACH TO THE DOUBLE-BUTTERING TECHNIQUE
In order for the double-buttering method to be more effective it must be carried out correctly. Various test campaigns have been carried out in order to define the most effective method and to get the most benefit possible.
It was found that it is better to apply the adhesive parallel to the short side of the tile (for tiles that are not square) and in the same direction on the substrate and on the rear side of the tile (do not apply the adhesive in a criss-cross pattern between the substrate and the tile; air bubbles could become trapped in the criss-crossed areas).
The reason why it is better to apply the adhesive parallel to the short side is that it helps expel any air when tapping the tiles into position by creating a shorter escape route. It was also found that the latest generation of notched trowels (with diagonal notches) are better at distributing the adhesive and can spread more adhesive than traditional trowels with square, triangular or semi-circular notches, particularly when applying adhesive on substrates. The shape of the trowel to use depends on the factors mentioned previously (the flatness and characteristics of the substrate, the size of the tiles and the thickness required for the layer of adhesive).
For example, from a series of tests carried out in Mapei Research & Development laboratories, it was found that, to install tiles with a longest side of more than one metre, the best results (on a flat substrate) were obtained by using a trowel with 10 mm square notches for the substrate and a trowel with 3 mm square notches for the rear side of the tiles. The level of buttering was obviously verified after tapping the tiles into position with hand tools or power tools (such as a vibrating plate).
The concepts discussed are contained in national standards in many countries, such as the standards DIN 18157 Part 1 or DIN 18157 Part 3 in Germany.
MAPEI ADHESIVES FOR TILES FOR AN EASY AND ECO-SUSTAINABLE INSTALLATION
Over the years, Mapei has formulated an increasingly large number of low-viscosity, highly-thixotropic adhesives characterised by their ease and speed of application. Adhesives such as ADESILEX P9 (particularly since recently changing its formula), KERAFLEX, KERAFLEX MAXI S1, ULTRALITE S1 and ULTRALITE S1 QUICK are very soft and creamy during application, but are still resistant to vertical slip, have excellent rib stability and slip-resistance, even when installing heavy tiles.
This is the result of the amount of effort and resources put into Research & Development by Mapei, which amounts to 5% of annual turnover and 12% of its workforce. This means intensive research and development in the name of innovation and sustainability, themes which Mapei pays great attention to. Mapei is also particularly committed to the health and safety of both the applicators and the final users of the products.
Mapei products do not affect the indoor air in our homes and guarantee health and comfort. The whole installation system is evaluated by LCA (Life Cycle Assessment), in order to measure the impact of the products on the environment throughout their whole life cycle: from extraction of the raw materials to their transport to the plant, the production, packaging, waste materials, the delivery to the distributor up to their final disposal.
Most of Mapei adhesives and grouts are certified with the EMICODE EC1PLUS logo, which guarantees products with very low emission of volatile organic compounds (VOC). The LCA approach allows us to measure how sustainable a product is for the environment, and the results are communicated through Environmental Product Declarations (EPD), documents verified and certified by a third party body.
Mapei’s commitment to sustainability also means using recycled materials. Innovative products with high quality and high durability, minimising the production of waste to be disposed and reducing the demand for natural materials, which contain no hazardous substances and have very low emission of VOC: these are all aspects that make Mapei products for ceramics more sustainable.