Video tutorials & spotlights

Webinars Reset filters

Webinars

Webinars, All Video Tutorials

MAPEI Webinar – MAPEI's cementitious flooring solutions

This presentation will provide an overview of MAPEI’s Ultratop systems of high-performance, polishable…

Ultratop [NA]

Mapefloor Finish 58 W [NA]

Primer SN [NA]

+ 9

Show products

Featured Products

Ultratop [NA]

Ultratop ® [NA] is a self-leveling, self-curing, sealed or polished topping that is specially formulated for fast-track resurfacing of horizontal wear surfaces.

Two-Component, Clear, Matte, Aliphatic Polyurethane Coating Mapefloor Finish 58 W [NA] is a two-component, aliphatic polyurethane coating in water dispersion with a clear, matte finish. Mapefloor Finish 58 W [NA] provides a high-performance finish on general-service resinous flooring products and Ultratop [NA] systems.

Primer SN [NA]

Primer SN ™ [NA] is a two-component, filled, epoxy primer specifically designed to enhance adhesion of cementitious flooring systems and multilayer resin flooring, such as MAPEI’s Mapefloor ™ products, Ultratop ® products, PlaniLevel ™ products and Planitop EL multilayer epoxy resin flooring systems and multilayer traffic deck systems.

Mapecrete Protector FF

High-Gloss, Film-Forming Protective Coating for Concrete Mapecrete Protector FF is a film-forming, high-gloss protective coating designed to increase the stain resistance of interior, polished or hard-troweled concrete floors.

Ultratop Loft F [NA]

Coarse-Textured, Cement-Based Micro-Topping Ultratop Loft F [NA] is a one-component, cement-based decorative topping that is troweled and applied in two layers 1/16" (1.5 mm) in thickness. It is specially formulated for abrasion resistance in designing non-uniform and non-homogeneous finishes with a broad range of coarse-textured finishing effects on indoor decorative surfaces. Ultratop Loft F [NA] can be used on a wide variety of substrates and combines excellent versatility with easy application.

Ultratop Loft W [NA]

Fine-Textured, Cement-Based Micro-Topping Ultratop Loft W [NA] is a one-component, cement-based decorative topping that is troweled and applied in two layers 1/16" (1.5 mm) in thickness. It is specially formulated for abrasion resistance in designing non-uniform and non-homogeneous finishes with a broad range of finishing effects on indoor decorative surfaces. Ultratop Loft W [NA] can be used on a wide variety of substrates and combines excellent versatility with easy application.

Epojet [NA]

Epojet ™ [NA] is a high-strength, two-component, 100%-solids, low-viscosity, epoxy resin for pressure injection and sealing of cracks in structural concrete, masonry and wood.

Epojet LV [NA]

Very Low-Viscosity, Epoxy Injection Resin for Crack Repair Epojet LV [NA] is a moisture-tolerant, two-component, 100%-solids, very low-viscosity, epoxy injection resin that deeply penetrates as well as seals dry and damp hairline, non-dynamic cracks. Epojet LV [NA] may be applied by pressure injection or gravity feed, and can also be combined with sand to become an epoxy mortar.

Mapefloor Finish 630 [NA]

Two-Component, Clear Protective Acrylic Coating for Floors Mapefloor Finish 630 [NA] is a two-component, protective, acrylic filming agent in a water dispersion for floors made from concrete and Ultratop systems. Mapefloor Finish 630 [NA] provides a high-performance finish on Ultratop systems.

Ultratop Base Coat [NA]

One-Component, Clear, Water-Based Acrylic Basecoat for Mapefloor Finish Topcoats Ultratop Base Coat [NA] one-component, acrylic agent in water dispersion is used as a basecoat before applying a Mapefloor Finish topcoat over Ultratop and Ultratop Loft products. Ultratop Base Coat [NA] used with Mapefloor Finish provides a high-performance finish.

Mapelux Opaca [NA]

Clear, Matte, Protective Wax for Ultratop and Ultratop Loft Systems Mapelux Opaca [NA] is a one-component, matte wax used as wear protector over MAPEI sealers permitted for Ultratop systems and Ultratop Loft systems only.

Ultratop SP

High-Performance, Polishable, Self-Leveling Topping for a Fine-Aggregate Finish Ultratop SP is a polishable, self-leveling, cementitious topping that provides a fine-aggregate exposed finish. Ultratop SP is engineered for fast-track resurfacing of horizontal wear surfaces.

All Video Tutorials, Webinars

MAPEI Webinar – The “silent destroyer”: Strategies to combat corrosion in reinforced concrete structures

Corrosion in concrete is a silent killer! Learn advanced strategies to combat rust, prevent structural damage…

Mapeshield I

Mapelastic

Mapefer 1K [NA]

+ 12

Show products

Featured Products

Mapeshield I

Pure Zinc Galvanic Anode Mapeshield I is a pure zinc anode for cathodic protection of reinforcing steel against corrosion in new, reinforced structures as well as structures requiring repair.

Mapelastic

Flexible, Cementitious Membrane for Waterproofing and Protecting Concrete and Masonry Mapelastic is a two-component cementitious membrane that waterproofs concrete and masonry. It also offers protection against chemical attack from de-icing salts, sulfates, chlorides and carbon dioxide.

Mapefer 1K [NA]

Mapefer ™ 1K [NA] is a one-component, anti-corrosion coating based on unique polymers, cementitious binders and corrosion inhibitors. Mapefer 1K [NA] is specially formulated for application on properly prepared reinforcing steel to inhibit oxidation and rust formation. This product features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions.

Mapeshield CI 100

Surface-Applied Corrosion Inhibitor Mapeshield CI 100 is a surface-applied corrosion inhibitor designed to penetrate concrete and protect embedded steel reinforcement. Mapeshield CI 100 delays the corrosion process and reduces overall corrosion activity.

Planitop 11 SCC

Self-Consolidating Concrete Mix with Corrosion Inhibitor Planitop 11 SCC is a one-component, cementitious, self-consolidating concrete mix with silica fume and a corrosion inhibitor for full-depth structural concrete repairs in above-, below- and on-grade applications.

Planitop 11

Pre-Extended, Pumpable and Pourable Concrete Mix Planitop 11 is a one-component, pre-extended, cementitious, pumpable and pourable concrete mix for full-depth concrete repairs in above-, below- and on-grade applications. Designed for large-volume repairs with application thicknesses from 1" (2.5 cm) to full depth, Planitop 11 is suitable for form-and-pour and form-and-pump applications. It is ideal for repairs on horizontal, vertical and overhead surfaces in applications such as tunnels, bridges, dams, parking garages, balcony edges and columns.

Planitop 18 ES

Very Rapid-Hardening Repair Mortar with Extended Working Time Planitop 18 ES is a one-component, high-early-strength, cementitious repair mortar, with a corrosion inhibitor, that has the very rapid-hardening characteristics of Planitop 18 but with an extended set and working time.

Planitop 12 SR

Sulfate-Resistant, Vertical, Overhead and Horizontal Repair Mortar with Silica Fume Planitop 12 SR is a sulfate-resistant, one-component, shrinkage-compensated, cementitious repair mortar. Planitop 12 SR is fiber-reinforced, contains both silica fume and a corrosion inhibitor, and is intended for the repair of vertical, overhead and horizontal concrete surfaces.

Planitop XS

Planitop ® XS is an extended-working-time variation of Planitop X . Shrinkage-compensated, fiber-reinforced, polymer-modified and containing a corrosion inhibitor, Planitop XS features Planitop X ’s outstanding workability and versatility. This product features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions.

Planibond 3C

Three-Component, Cementitious Corrosion Inhibitor and Bonding Agent Planibond 3C is a three-component, cementitious, moisture-tolerant, water-based, epoxy-modified corrosion inhibitor and bonding agent.

Mapecem 202

Medium-Build, Two-Component, Fast-Setting Mortar Mapecem 202 is a two-component, shrinkage-compensated, polymer-modified, fast-setting cementitious mortar with a corrosion inhibitor.

Planitop 15

Planitop ® 15 is a one-component, shrinkage-compensated, cementitious, fiber-reinforced, fluid mortar. Planitop 15 contains a corrosion inhibitor and silica fume, and is well-suited for form-and-pour and form-and-pump applications where high early strength and flowability are required.

Planitop X

One-Component, Fast-Setting, Fiber-Reinforced, Vertical and Overhead Repair Mortar Planitop X is a one-component, fiber-reinforced, shrinkage-compensated, high-early-strength, fast-setting, polymer-modified, high-build cementitious repair mortar with a corrosion inhibitor.

Planitop 23

Planitop ® 23 is a two-component, fast-setting, polymer-modified, thixotropic, fiber-reinforced cementitious repair mortar with a corrosion inhibitor. Planitop 23 is intended for vertical and overhead repairs, and contains silica fume to provide a durable, high-strength mortar in these applications.

Planitop 18

Very Rapid-Hardening Repair Mortar Planitop 18 is a very rapid-hardening repair mortar that exhibits high early strength and provides quick return to service.

Webinars, All Video Tutorials

MAPEI Webinar – Using sustainability to repair and maintain existing concrete & masonry buildings and infrastructure

Promoting sustainability, resiliency and ongoing maintenance to improve existing buildings and infrastructure…

Ultratop [NA]

Mapeshield I

Mapefer 1K [NA]

+ 8

Show products

Featured Products

Ultratop [NA]

Ultratop ® [NA] is a self-leveling, self-curing, sealed or polished topping that is specially formulated for fast-track resurfacing of horizontal wear surfaces.

Mapeshield I

Pure Zinc Galvanic Anode Mapeshield I is a pure zinc anode for cathodic protection of reinforcing steel against corrosion in new, reinforced structures as well as structures requiring repair.

Mapefer 1K [NA]

Planiseal CR1

Single-Component, 100%-Solids, Cold-Fluid-Applied, Structural Waterproofing Membrane Planiseal CR1 is a fast-curing, 100%-solids, cold-fluid-applied, single-component, moisture-curing, structural waterproofing membrane that will not shrink and is VOC-compliant in virtually all municipalities. Very low in odor, it is well suited for use in and around occupied spaces. Thanks to advanced proprietary technology, this single-grade membrane can be used in horizontal as well as vertical applications, maximizing versatility. Planiseal CR1 can be applied by roller, brush, trowel or squeegee. Planiseal CR1 is Miami-Dade NOA approved for: Exterior Waterproofing under Porcelain Tiles (System Type F) Planters (System Type F2) Concrete Split Slab Assemblies (System Type F3) The Miami-Dade Notice of Acceptance (NOA) designates that the approved product meets Florida Building Code (FBC) High Velocity Hurricane Zone (HVHZ) requirements. Many coastal municipalities accept or require this NOA in their local building code. Always confirm the most current requirements per the local code.

Epojet [NA]

Epojet ™ [NA] is a high-strength, two-component, 100%-solids, low-viscosity, epoxy resin for pressure injection and sealing of cracks in structural concrete, masonry and wood.

Epojet LV [NA]

Planiseal WR 40

Water-Based, 40%-Silane, Penetrating Water Repellent Planiseal WR 40 is a water-based, 40%-silane, penetrating water repellent and sealer designed to protect concrete and masonry against moisture/chloride intrusion.

Planiseal WR

Penetrating, Water-Based, Silane/Siloxane Water Repellent Planiseal WR is a silane/siloxane-blend, water-repellent, transparent sealer that provides resistance to water, dirt and chlorides.

Planiseal 88

Cement-Based, Waterproofing and Surface-Preparation Coating Planiseal 88 is a one-component, polymer-modified, cementitious coating for waterproofing, including masonry surfaces, at a maximum depth of 10 feet (3,05 m). Planiseal 88 is also used as a surface-preparation product for MAPEI waterproofing products.

Planibond 3C

Concrete Renew

High-Performance Concrete Resurfacer Concrete Renew is a one-component, polymer-modified, cementitious material for the resurfacing of existing concrete to provide a like-new look to concrete surfaces.

All Video Tutorials, Featured Videos, Webinars

MAPEI Webinar – Transforming returned concrete: From waste to resource

This presentation focuses on the topic of reclaiming returned concrete and turning it into recyclable…

Re-Con Zero Evo US

Mapefibre F

Mapefibre M

+ 2

Show products

Featured Products

Re-Con Zero Evo US

Two-Component Powder for Recovering Returned Concrete from Mixer Trucks Re-Con Zero Evo US is a two-component powder product used to recover all “returned concrete” with zero impact on the environment and zero investment required for reclaiming plants.

Mapefibre F

Fibrillated Fiber Reinforcement System for Concrete Mapefibre F (formerly known as Polymesh F) are fibrillated polypropylene microfibers manufactured from 100%-virgin polypropylene resins. Mapefibre F ’s fibrillation pattern improves the bonding between fibers and the concrete mixture, thus improving plastic shrinkage control in concrete.

Mapefibre M

Monofilament Fiber Reinforcement System for Concrete Mapefibre M (formerly known as Polymesh M) are monofilament polypropylene microfibers manufactured from 100%-virgin polypropylene resins. Mapefibre M ’s primary application is plastic shrinkage control in concrete.

Mapecube 1

Strength-Enhancing Liquid Admixture for Concrete and Mortar Mapecube 1 is a chloride-free, strength-enhancing liquid admixture for concretes and mortars, developed by MAPEI to optimize the hydration of cement. Mapecube 1 is particularly suitable for projects that require high early strength. Mapecube 1 allows for the reduction or elimination of steam curing, as well as reduction of cement content and continued production in colder ambient conditions. Mapecube 1 meets or exceeds the requirements of ASTM C494, Type S, and AASHTO M194, Type S.

Re-Con AGG 100 [NA]

Plasticizing Admixture for Use with Recycled-Aggregate Concrete Re-Con AGG 100 [NA] is a modified, acrylic, polymer-based plasticizer developed for use in ready-mixed concrete with recycled aggregates as well as with materials that have a high-water demand, such as clay-bearing aggregates and sand with high free mica content. Re-Con AGG 100 [NA] meets the requirements of ASTM C494, Type B, and AASHTO M194, Type B.

All Video Tutorials, Webinars

MAPEI Webinar – From cracks to strength: A comprehensive approach to concrete-bridge repair

This Webinar focuses on the critical need for advanced concrete-bridge repair products. Topics discussed…

Mapeshield I

MapeWrap C Bi-Ax

Maperod C

+ 22

Show products

Featured Products

Mapeshield I

Pure Zinc Galvanic Anode Mapeshield I is a pure zinc anode for cathodic protection of reinforcing steel against corrosion in new, reinforced structures as well as structures requiring repair.

MapeWrap C Bi-Ax

High-Strength, Bi-Directional Carbon Fiber Fabric MapeWrap C Bi-Ax is a high-strength, bi-directional carbon fiber fabric in which the primary fibers are oriented in the 0°/90° directions. When used with the MapeWrap family of two-component epoxy adhesives, MapeWrap C Bi-Ax forms an externally bonded fiber-reinforced polymer (FRP) reinforcement system engineered to increase the strength of existing structural elements. When applied to the surface of structural members in buildings, parking garages, bridges, marine piles and other structures, MapeWrap C Bi-Ax contributes significant strength with minimal increase to the dead load supported by the structure.

Maperod C

High Tensile Bars Pre-Formed with Epoxy Resin Pultruded carbon fibre or glass fibre bars for repairing and structural strengthening damaged concrete, wooden and masonry elements. Maperod C : high tensile bars pre-formed with epoxy resin

Maperod G

MapeWrap C Uni-Ax System

High-Strength, Uni-Directional Carbon Fiber Fabric MapeWrap C Uni-Ax is a high-strength, uni-directional carbon fiber fabric that, when used with the MapeWrap family of two-component epoxy adhesives, forms an externally bonded fiber-reinforced polymer (FRP) reinforcement system. MapeWrap C Uni-Ax fabric is part of an engineering solution that allows for an increase in the strength of structural elements without increasing the dead load supported by the structure. It is available in different weights (300, 600, 900 and 1200), each with different heights.

Carboplate E 170

Pultruded Carbon Fiber Plate Pre-Impregnated in Epoxy-Based Resin Carboplate E 170 is a range of pultruded carbon-fiber-reinforced polymer (CFRP) plates designed for external structural strengthening of existing concrete, wood, masonry and steel members. Carboplate E 170 is externally bonded onto the surface of the substrate to strengthen and stiffen existing structures, using an epoxy resin specifically designed for the application. Carboplate E 170 is protected on both sides by a plastic film, eliminating the need for solvent cleaning of the plates before installation.

MapeWrap G Uni-Ax

High-Strength, Uni-Directional E-Glass Fiber Fabric MapeWrap G Uni-Ax is a high-strength, uni-directional E-glass fiber fabric that, when used with the MapeWrap family of two-component epoxy adhesives, forms an externally bonded fiber-reinforced polymer (FRP) reinforcement system engineered to increase the strength of structural elements. When applied to the surface of structural members in buildings, parking garages, bridges, marine piles and other structures, MapeWrap G Uni-Ax improves the seismic performance of concrete columns, masonry and concrete walls, and concrete beam-column connections.

Planibond SBA

Normal-Set, Segmental Bridge Adhesives Planibond SBA epoxy bonding adhesives are two-component, 100%-solids and moisture-insensitive. Each Planibond SBA adhesive acts as a lubricant and sealer for match-cast precast segments used in span by span and cantilevered erection of segmented precast elements.

Mapefer 1K [NA]

Planibond AE Fast

Rapid-Setting, High-Strength, Epoxy Anchoring Gel Planibond AE Fast is a rapid-setting, high-strength, moisture-tolerant, two-component, 100%-solids, epoxy anchoring gel designed for a wide variety of vertical/horizontal bonding and repair applications.

Planitop 11 SCC

Planitop 11

Planitop 18 ES

Planitop 12 SR

Planitop XS

Planiseal WR

Penetrating, Water-Based, Silane/Siloxane Water Repellent Planiseal WR is a silane/siloxane-blend, water-repellent, transparent sealer that provides resistance to water, dirt and chlorides.

Planibond AE

High-Strength, Nonsag, Epoxy Anchoring Gel Planibond AE is a high-strength, moisture-tolerant, zero-VOC, two-part, nonsag, epoxy anchoring gel designed for a wide variety of bonding and repair applications.

Planiseal Traffic Coat

Planiseal ® Traffic Coat is a moisture-tolerant, 100%-solids, low-modulus, two-part, epoxy binder engineered for providing a skid-resistant overlay on elevated concrete decks.

Planibond 3C

Planitop 15

Planitop 23

Planitop X

Planigrout PT

Post-Tensioning Grout Planigrout PT is a non-shrinking, fluid, cement-based grout used to fill the annular space around post-tensioned strands in PT ducts.

Planitop 18

Very Rapid-Hardening Repair Mortar Planitop 18 is a very rapid-hardening repair mortar that exhibits high early strength and provides quick return to service.

Planitop 18 TG

Very Rapid-Hardening, Trowel-Grade, High-Early-Strength Repair Mortar Planitop 18 TG is a one-component, shrinkage-compensated, very rapid-hardening, trowel-grade, cementitious repair mortar with a corrosion inhibitor. Planitop 18 TG gains strength rapidly and is particularly suited for all horizontal concrete repairs from 1/2" to 2" (12 mm to 5 cm) thickness when applied neat and up to 8" (20 cm) when extended with aggregate.

All Video Tutorials, Webinars

MAPEI Webinar – Floor Covering Installation Systems product-line review

Get an understanding of the current and active product assortment for MAPEI’s FCIS line. Learn about changes…

Ultrabond ECO 303

Ultrabond ECO MS 4 LVT Wall [NA]

Ultrabond ECO MS 4 LVT [NA]

+ 70

Show products

Featured Products

Ultrabond ECO 303

Floor-Repair Adhesive Ultrabond ECO 303 is a proprietary water-based adhesive formulation designed to be injected under existing wood, tile or resilient flooring to fill hollow spots or areas that have become unbonded. Once cured, Ultrabond ECO 303 provides a secure and elastomeric bond, reducing hollow sounds under foot and securing loose flooring materials. AVAILABLE AT SELECT RETAIL LOCATIONS ONLY

Ultrabond ECO MS 4 LVT Wall [NA]

Professional, Hybrid-Polymer Adhesive for Resilient Flooring on Walls Ultrabond ECO MS 4 LVT Wall [NA] is a moisture-curing, one-component, thixotropic, silane-modified polymer adhesive specifically designed for the direct bonding of various resilient flooring types in both wall and floor installations.

Ultrabond ECO MS 4 LVT [NA]

Professional, Hybrid-Polymer Adhesive for Resilient Flooring Ultrabond ECO MS 4 LVT [NA] is a moisture-curing, one-component, silane-modified, hybrid-polymer adhesive specifically designed for the direct bonding of vinyl and rubber flooring in interior applications.

Planislope RS

Rapid-Setting, Polymer-Modified Sloping Mortar Planislope RS is a rapid-setting, pre-blended, cement-based, polymer-modified mortar that includes a blend of selected aggregates for use in sloping and thick- bed mortar installations. It only needs mixing with water to produce a mortar of exceptional strength. Used for preparing a substrate before the installation of tile and stone, Planislope RS is designed for pre-sloping under waterproofing membranes and mortar beds in showers when quick turnarounds are desired.

Planiseal PMB

One-Component, Polyurethane Moisture Barrier and Bonding Agent Planiseal PMB is a one-component, moisture-curing, polyurethane compound designed to provide moisture vapor emission protection on damp concrete substrates in a single- or double-coat application method as well as a vapor retarder using a single-coat method over wood substrates. It also serves as a bonding agent and moisture barrier system for self-leveling underlayments when applied in a double-coat method with dry sand.

Mapecoat 4 LVT [NA]

Two-Component, Water-Based, Aliphatic, Anti-Slip, Polyurethane Finish for LVT Mapecoat 4 LVT [NA] is a transparent protective finish that comes in matte (10 gloss) and semi-gloss (30 gloss) for luxury vinyl tile (LVT) in addition to other resilient flooring in horizontal and vertical applications. It provides a non-slip finish with high resistance to wear in residential and commercial environments, including wet areas such as tub surrounds and shower enclosures as well as dry areas that are subject to high foot traffic.

Ultrabond ECO 904

Stair-Nose Adhesive Ultrabond ECO 904 is a proprietary adhesive formulation designed to bond stair nosing on common wood and concrete substrates. Once cured, Ultrabond ECO 904 provides a secure and rigid bond for wood, laminate and rigid PVC stair-nosing materials. AVAILABLE AT SELECT RETAIL LOCATIONS ONLY

Ultrabond ECO 379

Ultrabond ECO ® 379 is an aggressively pressure-sensitive adhesive resistant to high moisture and to heavy rolling loads. It is designed for fast-track roller application, reducing time spent in adhesive application.

Ultracoat Easy

Standard-Performance, Water-Based, Polyurethane Wood-Flooring Finish Ultracoat Easy is an economical, one-component, water-based wood-flooring finish that is available in the gloss levels of matte, satin and semi-gloss. Suitable for use in interior residential applications, Ultracoat Easy is a self-crosslinking, aliphatic polyurethane resin base with excellent abrasion resistance for solid, pre-sanded wood floors.

Ultrabond ECO 399

Heavy-Duty, Pressure-Sensitive, Multi-Flooring Adhesive Ultrabond ECO 399 is a high-moisture-resistant, heavy-rolling-load-resistant, aggressive, pressure-sensitive adhesive with enhanced dimensional control properties designed to install a wide variety of resilient flooring types. Ultrabond ECO 399 can also be used for flash-coving installations using traditional installation methods.

Novoplan HFL

High-Flow, Self-Leveling Compound Novoplan HFL is a self-leveling, calcium-aluminate-based underlayment and repair mix for interior concrete and engineer-approved floors with high-flow characteristics.

Ultrabond ECO 903

Tongue and Groove Glue Ultrabond ECO 903 is a high-performance, high-solids, acrylic, latex-based adhesive designed for the bonding of floating wood flooring or for general wood carpentry purposes.

Ultrabond ECO 2285

Premium, Universal Seam Sealer for Carpet Ultrabond ECO 2285 is recommended for seaming/sealing most types of carpet in a direct glue-down installation. Ultrabond ECO 2285 can also be used in double-stick applications.

Ultracoat Premium Base

Ultracoat ® Premium Base is a two-component, high-performance, water-based sanding sealer for all types of wood flooring – including exotic species – and is specifically designed to work with Ultracoat water-based finishes in high-traffic areas. Ultracoat Premium Base seals freshly sanded wood flooring and creates a base layer that isolates the finish coat from penetrating into the open wood surface. Ultracoat Premium Base is formulated to enable a single-coat application for most wood types.

Novoplan DPL

Deep-Pour, Self-Leveling Compound Novoplan DPL is a self-leveling, calcium-aluminate-based underlayment and repair mix for interior concrete and engineer-approved floors and is capable of being placed up to 4" (10 cm) in a single lift.

Ultracoat Toning Base

Two-Component, Deep-Tone Sanding Sealer Ultracoat Toning Base is a two-component, deep-tone, water-based sanding sealer for all types of wood flooring – including exotic species – and is designed to enhance the natural color of wood without causing it to darken or redden. Ultracoat Toning Base provides a deep look similar to what solvent-based sealers offer and is specifically designed to work with Ultracoat water-based finishes. Ultracoat Toning Base seals freshly sanded wood flooring and creates a base layer that isolates the finish coat from penetrating into the open wood surface.

Ultracoat HT 2K

Two-Component, Water-Based, Polyurethane Wood-Flooring Finish Ultracoat HT 2K is a two-component, water-based wood-flooring finish that is available in the gloss levels of natural, matte, satin and semi-gloss. Suitable for use in interior residential and heavy commercial applications where extreme traffic is expected, Ultracoat HT 2K is an aliphatic polyurethane resin system with excellent abrasion resistance for solid, pre-sanded wood floors. Ultracoat HT 2K adds a warm color to the wood and is non-yellowing.

Ultracoat Aqua Plus

Sawdust Admixture for Crack Filling of Wood Flooring Ultracoat Aqua Plus is a single-component binder that is mixed with sawdust produced during the final sanding process of preparing wood floors, and used to fill voids and cracks before the final application of water-based wood-floor finishing systems. Ultracoat Aqua Plus has extremely high wetting properties, is low in viscosity and forms a high-solids paste with excellent adhesion and workability. After application, the mixture dries quickly and can be sanded easily. The remaining mixture can be stored in a sealed plastic container.

Ultracoat Easy Plus

One-Component, Water-Based Polyurethane Wood-Flooring Finish Ultracoat Easy Plus is a one-component, water-based wood-flooring finish that is available in the gloss levels of matte, satin and semi-gloss. Suitable for use in interior residential and light commercial applications, Ultracoat Easy Plus is a self-crosslinking, aliphatic polyurethane resin system with excellent abrasion resistance for solid, pre-sanded wood floors. Ultracoat Easy Plus adds a warm color to the wood and is non-yellowing.

Ultrabond ECO 575 [NA]

Premium Wall-Base Adhesive Ultrabond ECO 575 [NA] is a premium wall-base adhesive specifically designed to provide superior bond and impact resistance for rubber, vinyl and carpet wall base. Ultrabond ECO 575 [NA] also has been reformulated to offer even greater grab and wet strength, keeping corners wrapped tight. Its light-colored, water-based, acrylic-polymer formulation won't stain even the whitest wall base.

Ultrabond ECO 185

Professional Carpet Adhesive Ultrabond ECO 185 is a latex-based adhesive that offers fast grab and quick leg development for the fast-track installation of commercial carpet. It can be used in direct-bond and double-stick carpet applications.

Ultrabond ECO 350

Professional, Solid Vinyl Flooring Adhesive Ultrabond ECO 350 is a proprietary formulation based on a MAPEI acrylic polymer. It offers the unique flexibility of installing floor coverings after a short flash time or once the adhesive exhibits pressure-sensitive characteristics. Easy to apply and low in odor, Ultrabond ECO 350 is perfectly suited for the installation of flooring in occupied environments.

Ultrabond ECO 977

Fast-Set Urethane Adhesive for Hardwood Flooring Ultrabond ECO 977 is a fast-setting, 100%-solids, one-component, moisture-cured urethane adhesive specifically designed for the installation of domestic solid and engineered wood flooring. Ultrabond ECO 977 can also be used in elevated subfloor moisture conditions of up to 12 lbs. (5.44 kg) MVER and 95% relative humidity when a specific installation method and trowel notch configurations are used.

Ultrabond ECO 907

Fast-Curing, Silane-Modified Polymer Adhesive Ultrabond ECO 907 is a fast-curing, 100%-solids, moisture-curing, gun-grade adhesive designed for basic wood subfloor construction practices as well as repairing of wood flooring; bonding of wood stair nosings; installation of wood molding and baseboards; and attachment of tackstrips to concrete subfloors. Ultrabond ECO 907 is also ideal for supplemental bonding of wide plank boards when nailing and gluing are required.

Ultracoat Gym Pro

High-Performance, Cross-Linked, Water-Based, Polyurethane, Gym Wood-Flooring Finish Ultracoat Gym Pro is two-part, aziridine cross-linked, water-based, high-performance formula designed to provide a high-gloss finish for professional, wood sports floors.

Ultracoat Gym

One-Component, Water-Based, Polyurethane, Gym Wood-Flooring Finish Ultracoat Gym is a one-part, water-based formula designed to provide a high gloss finish for professional gym floors. It is a self-crosslinking, aliphatic polyurethane resin system with excellent abrasion resistance and slip resistance suitable for solid, pre-sanded, wood sports floors.

Planiseal MSP

Moisture-Control Membrane, Adhesive Isolator, Sealer, pH Blocker and Primer Planiseal MSP is a two-coat, high-solids, polymer-based adhesive isolator, sealer, moisture-control membrane and self-leveling primer. Planiseal MSP protects flooring installations against subfloor moisture and pH in concrete slabs with moisture vapor emission rates (MVERs) up to 15 lbs. (6.80 kg) per ASTM F1869, relative humidity (RH) up to 99% per ASTM F2170 and alkalinity protection up to pH of 12. Planiseal MSP eliminates the need for a secondary primer for self-leveling applications.

Ultrabond ECO 373

Universal, Pressure-Sensitive, Multi-Flooring Adhesive Ultrabond ECO 373 is a super aggressive, pressure-sensitive adhesive that is designed for the installation of a wide variety of resilient flooring types. Ultrabond ECO 373 has been specifically formulated to provide extended working time and can be applied using a trowel or roller, depending on the level of tack that is required for the flooring that is being installed. Ultrabond ECO 373 can also be used for flash-coving installations using traditional installation methods.

Ultracoat ReNewIt Remover

Cleaner and Polish Remover Ultracoat ReNewIt Remover is a high-performance cleaning solution and polish remover. It is designed to remove polishes, stubborn dirt, oil and debris as the first step in preparing LVT, VCT, resilient, hardwood or bamboo flooring to be recoated with floor finish. After flooring is treated with Ultracoat ReNewIt Remover , it can be cleaned with Ultracoat ReNewIt Cleaner and then coated with Ultracoat ReNewIt Primer in preparation for a new floor finish.

Ultracoat ReNewIt Primer

Two-Component Primer and Bonding Agent Ultracoat ReNewIt Primer is a proprietary, high-performance, two-component, water-based primer and bonding agent designed as the third step in preparing LVT, VCT, resilient, wood or bamboo flooring to be resurfaced with Ultracoat HT 2K .

Ultraplan Extreme 2

Weather-Resistant, High-Compressive-Strength, Self-Leveling Underlayment Ultraplan Extreme 2 is an advanced, hydraulic-cement-based, self-leveling compound designed for fast-track underlayment applications. It is especially formulated for leveling interior, horizontal concrete surfaces where environmental controls are not operational or the building is not enclosed. Once installed, Ultraplan Extreme 2 is not affected by exposure to intermittent rain exposure after 6 hours or to freezing temperatures after 3 days of curing. Its high compressive strength is designed to allow it to be exposed to traffic as a temporary wear layer until the floor is covered with floor covering. Ultraplan Extreme 2 has no moisture vapor emission limitations and can be installed without testing on properly prepared concrete substrates. It is the self-leveling compound of choice for use under moisture-controlling adhesive systems and epoxy moisture barriers.

Ultrabond ECO 983

Modified-Silane, Moisture-Control Wood-Flooring Adhesive Ultrabond ECO 983 is a single-component, 100%-solids, modified-silane wood-flooring adhesive that is formulated without water, solvents, amines, isocyanates, phthalate plasticizers or epoxy resins. With an extremely low emission level of volatile organic compounds (VOCs), the unique formulation of Ultrabond ECO 983 provides excellent bond strength and moisture control up to 15 lbs. (6.80 kg) MVER and 90% relative humidity (RH). Special trowel clips are provided to apply the adhesive in a monolithic layer for subfloor moisture control. It can also be used with traditional trowel-applied methods where subfloor moisture problems do not exist.

Ultracoat ReNewIt Cleaner

Spot-Free Cleaner and Rinsing Solution Ultracoat ReNewIt Cleaner is a high-performance, spot-free cleaning and rinsing solution designed to remove any remaining U ltracoat ReNewIt Remover and dirt as the second step in preparing LVT, VCT, resilient, wood or bamboo flooring to be recoated with floor finish. It can also be used as a general cleaner for all flooring types.

Ultraplan Lite

Lightweight, Self-Leveling Underlayment Ultraplan Lite is a polymer-modified, calcium-aluminate-based, lightweight, self-drying, self-leveling underlayment. It has been specifically designed for use for leveling substrates that are not rated to carry the full weight of a traditional self-leveling underlayment. Ultraplan Lite mixes easily and flows out to a suitable finish with a final dry density of about 67 lbs. per cu. ft. (1 073 kg per m³) at 28 days.

Novoplan Easy Plus

Easy-Preparation, Self-Leveling Underlayment Novoplan Easy Plus is a high-strength, self-leveling, calcium-aluminate-based underlayment and repair mix for interior concrete and engineer-approved floors. Its unique formulation allows for direct application on substrates that are clean, securely bonded and properly primed.

Novoplan 2 Plus

Professional, Self-Leveling Underlayment Novoplan 2 Plus is a high-strength, self-leveling, cement-based underlayment and repair mix for interior concrete and engineer-approved floors.

Planiseal VS Fast

Fast-Track, Alkali-Resistant, Epoxy Moisture-Reduction Barrier Planiseal VS Fast is a fast-curing, alkali-resistant, two-component, 100%-solids epoxy coating that effectively stops moisture-related problems over concrete that impact floor coverings. In addition, it significantly expedites floor installations by eliminating the traditional wait time required for new concrete slabs to reach moisture levels suitable for floor-covering installation.

Ultrabond ECO 985

Hybrid-Polymer-Based, Moisture-Control and Sound-Reducing Wood-Flooring Adhesive Ultrabond ECO 985 is MAPEI’s premium single-component, hybrid-polymer-based wood-flooring adhesive that is formulated without water, solvents, amines, isocyanates, phthalate plasticizers or epoxy resins, and has an extremely low emission level of volatile organic compounds (VOCs). Ultrabond ECO 985 ’s formulation provides excellent sound-reduction properties that are required for multi-unit housing. Ultrabond ECO 985 is also a moisture-controlling wood-flooring adhesive that protects wood flooring from moisture vapor emitting through concrete slabs in a single application.

Ultraplan M20 Plus

Quick-Setting, High-Compressive-Strength, Self-Leveling Underlayment Ultraplan M20 Plus is a calcium-aluminate-based, quick-setting, self-leveling underlayment and topping. It is specially formulated for the resurfacing and construction of interior horizontal surfaces as a high-compressive-strength underlayment with maximum resistance to wheel tracking and indentations. Ultraplan M20 Plus is suitable for use as a commercial wear topping in warehouse and alternate industrial applications where an exceptional flat and smooth concrete surface is desired.

Ultraplan Easy

High-Performance, Easy-Preparation, Self-Leveling Underlayment Ultraplan Easy is a quick-setting, self-leveling underlayment that requires only a clean, soundly bonded, properly prepared and primed substrate before application.

Primer T

Primer T ™ is a low-VOC, magenta-colored, water-based acrylic primer that enhances the performance and adhesion of self-leveling underlayments (SLUs) on nonporous and porous substrates. Suitable for a wide variety of substrates, Primer T combines excellent versatility with easy, low-odor application.

Ultrabond ECO 995

Premium Moisture-Control, Sound-Reduction and Wood-Flooring Adhesive Ultrabond ECO 995 is MAPEI’s premium, 100%-solids, one-component, moisture-curing urethane adhesive for all types of wood flooring and bamboo. Ultrabond ECO 995 can be used in a single-coat application method that provides a superior bond with moisture vapor emission control on concrete slabs. Ultrabond ECO 995 also provides sound-reduction properties, making it suitable for use in multi-unit housing projects.

Planiseal VS

Alkali-Resistant, Epoxy Moisture-Reduction Barrier Planiseal VS is an alkali-resistant, two-component, 100%-solids epoxy coating that effectively stops moisture-related problems over concrete with floor coverings. In addition, Planiseal VS expedites floor-covering installations by eliminating the traditional wait time required for new concrete slabs to reach moisture levels suitable for installations.

Primer CE

Ultra Low-Viscosity, Consolidating, Epoxy Primer Primer CE is an ultra low-viscosity, two-component, 100%-solids surface-consolidating, epoxy primer. Primer CE effectively penetrates and consolidates the surface of weak concrete or gypsum substrates. Applied in a single-coat application, Primer CE is designed to restore structural integrity to friable substrates such as weak gypsum-based underlayments or lightweight concretes before the application of underlayments, toppings or floor finishes. Once installed, Primer CE is compatible with a wide number of primers and adhesives typically used with flooring installations, such as with tile, vinyl composition tile (VCT), carpet, sheet vinyl, wood and other floor-finishing products.

Primer E

High-Performance, 100%-Solids, Epoxy Primer Primer E is a two-component, 100%-solids, epoxy primer and bonding agent designed for use with MAPEI self-leveling underlayments using MAPEI’s sand broadcast method. Primer E is the most effective method for bonding to nonporous, dense substrates before installing self-leveling underlayments subject to high stress. Primer E’ s low viscosity makes installation fast and easy, and provides excellent penetration into the substrate and therefore a tenacious bond.

Ultrabond ECO 3185

Ultrabond ECO ® 3185 latex carpet pad adhesive is a water-based adhesive for fastening carpet padding permanently in place over any flooring surface. It has good initial tack and high strength to prevent movement of padding during stretching or subsequent use. Ultrabond ECO 3185 has no solvent added and is nonflammable, making it suitable for use in enclosed environments in occupied buildings.

Topcem Premix

Accelerated-Cure Screed

Ultrabond ECO 20

Standard Flooring Adhesive Ultrabond ECO 20 has been designed to provide both value and performance in a standard flooring adhesive. Its unique formulation provides ample working time for installing felt-backed vinyl sheet flooring, smooth-backed carpet and rough-backed carpet.

Ultrabond ECO 980

Premium Urethane Adhesive for Hardwood Flooring Ultrabond ECO 980 is a 100%-solids, one-component, moisture-cured urethane adhesive specifically designed for the installation of domestic and exotic solid and engineered wood flooring, including bamboo.

Ultrabond ECO 975

Standard, Urethane Adhesive for Hardwood Flooring Ultrabond ECO 975 is a 100%-solids, one-component, moisture-cured, urethane adhesive specifically designed for the installation of domestic solid and engineered wood flooring.

Ultrabond ECO 711

Premium, Clear, Thin-Spread VCT Adhesive Ultrabond ECO 711 is a latex-based adhesive that offers a quick drying time with enhanced grab and slip resistance for vinyl composition tile (VCT) installations. Ultrabond ECO 711 is translucent when dry, allowing layout lines to be easily seen.

Ultrabond ECO 220

Premium Flooring Adhesive Ultrabond ECO 220 is a high-solids, latex-based adhesive designed specifically for installing carpet and felt-backed vinyl sheet flooring. Its unique formulation is perfectly suited for commercial flooring applications where heavy traffic is expected. Ultrabond ECO 220 also exhibits an extended working time, making it ideal for the installation of patterned carpets. It may be used in both direct and double glue-down installation methods for carpet.

Ultrabond ECO 360

Premium, High-Performance Adhesive for Solid Vinyl Sheet, Tile and Plank Ultrabond ECO 360 is a proprietary, high-performance, wet-lay and pressure-sensitive adhesive designed specifically for installing homogeneous and heterogeneous solid vinyl flooring. With its strong, durable, moisture-resistant and alkali-resistant bond, it is ideal for commercial and institutional applications. Ultrabond ECO 360 has an excellent open time, develops strength quickly, performs well under rolling loads and resists indentation. Its low volatile organic content makes it ideal for use in occupied buildings such as hospitals and medical centers.

Ultrabond ECO 420

High-Performance, Moisture-Resistant, Indoor/Outdoor Carpet Adhesive Ultrabond ECO 420 is a proprietary, water-based adhesive formulation designed for both indoor and outdoor carpet. Ultrabond ECO 420 offers high-moisture-resistant characteristics and excellent bond properties for interior and exterior broadloom carpet installations. Ultrabond ECO 420 is also perfectly suited to bond reground rubber underlayments such as Mapesonic RM for ceramic tile installations. Due to its unique formulation, it can be installed without the need for moisture testing.

Ultrabond G21

Premium, Two-Part, Urethane Flooring Adhesive Ultrabond G21 is a two-part, reactive adhesive with low volatile organic compounds (VOCs), designed for extreme indoor and outdoor flooring installations. This adhesive aggressively adheres all types of floor coverings to properly prepared metal, asphalt pavement and many other difficult-to-bond-to substrates.

Ultrabond G19

Professional, Two-Part, Urethane Flooring Adhesive Ultrabond G19 is a two-part, epoxy-modified, polyurethane reactive adhesive specially designed for the installation of floor coverings in high-performance applications in both interior and exterior applications.

Primer L

Advanced-Technology, Acrylic Latex Primer for Concrete Primer L is a concentrated, solvent-free acrylic primer used before the installation of underlayment materials. It is green for easy identification. Primer L improves the bond between a properly prepared and profiled concrete substrate, and a self-leveling underlayment. Primer L can also be used as a primer for gypsum-based underlayments and patches.

Primer WE

Water-Based Epoxy Primer Primer WE is a two-component, polymer-modified, water-based, epoxy primer for enhanced adhesion to nonporous substrates before the application of MAPEI self-leveling materials. It improves adhesion over smooth, nonabsorbent and difficult-to-bond-to substrates such as properly prepared glazed ceramic tile, epoxy moisture barriers, cement-based terrazzo, old cutback adhesive residue and approved plywood subfloors.

Planipatch Plus

High-Performance Additive for Planipatch Planipatch Plus is an acrylic latex additive for use specifically with Planipatch fast-setting, polymer-modified, cement-based patching compound. Mixing Planipatch Plus undiluted with Planipatch allows it to be used over a variety of substrates including vinyl composition tile (VCT), felt-backed sheet vinyl, cutback adhesive residue and MAPEI moisture barriers.

Ultraplan 1 Plus

High-Performance, Quick-Setting, Self-Leveling Underlayment Ultraplan 1 Plus is a quick-setting, self-leveling, self-drying underlayment and repair mix for interior concrete and engineer-approved floors. Ultraplan 1 Plus has high strength and is abrasion-resistant, able to withstand light foot traffic after 2 to 3 hours and vehicular rubber-wheel traffic after 3 days.

Ultrabond Urethane Cleaner

Professional Adhesive Remover Ultrabond Urethane Cleaner is a ready-to-use urethane adhesive cleaner designed to effectively remove wet urethane adhesive residues, such as Ultrabond ECO 975 , Ultrabond ECO 980 , Ultrabond ECO 990 and Ultrabond ECO 995 , from the surface of prefinished wood flooring. It is low-odor, nonflammable, pH-neutral and biodegradable. Safe for use on most types of prefinished wood flooring including parquet, engineered, solid and bamboo, Ultrabond Urethane Cleaner also removes urethane adhesive from trowels and tools.

Mapecem Quickpatch

High-Performance Concrete Patch Mapecem Quickpatch is a high-performance, fast-setting, cementitious material used for the patching of concrete surfaces. This product features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions.

ECO Prim Grip

Multipurpose, Bond-Promoting Primer ECO Prim Grip is a ready-to-use, low-VOC, synthetic resin-based primer with bond-promoting silica aggregates suspended in dispersion. It enhances the performance and adhesion of mortars to existing ceramics and difficult-to-bond-to substrates. Plus, it improves bonding of self-leveling underlayments (SLUs) and bonds of render coats over cementitious substrates. Suitable for a wide variety of substrates, ECO Prim Grip combines excellent versatility with an easy, low-odor application.

Planipatch

Fast-Setting, Polymer-Modified, Cement-Based Patching Compound Planipatch is an ultra fast-drying, self-curing, polymer-modified, cement-based patching compound that rapidly develops high compressive strength. When Planipatch is mixed with Planipatch Plus , the Planipatch Plus System can be used as an embossing leveler or as a patch to fill voids over properly prepared vinyl sheet goods, vinyl composition tile (VCT) and cement terrazzo before the direct glue-down installation of floor coverings.

Ultracoat Universal Base

Ultracoat ® Universal Base is a one-component, rapid-drying, water-based sanding sealer for solid, engineered and exotic wood flooring. Specifically designed to work with Ultracoat water-based finishes, Ultracoat Universal Base seals freshly sanded wood flooring and creates a base layer that isolates the finish coat from penetrating into the open wood surface.

Planiprep PSC

Moisture-Resistant, Fast-Drying Patch and Skimcoating Compound Planiprep PSC is a fast-drying, cement-based, fiber-reinforced, polymer-modified patch and skimcoating compound designed for preparing concrete and wood substrates for flooring installation.

Ultrabond ECO 570

Premium, Urethane Rubber-Sports-Flooring Adhesive Ultrabond ECO 570 is a moisture-curing, one-component, polyurethane polymer adhesive specifically designed for the direct bonding of high-performance reground-rubber sports flooring in interior or exterior applications. Its unique formulation is perfectly suited for most types of reground-rubber sports flooring and provides an aggressive and durable bond. Ultrabond ECO 570 utilizes rapidly renewable raw materials as part of the formulation and is free of phthalate plasticizers.

Planiprep SC

High-Performance, Fiber-Reinforced Skimcoating Compound Planiprep SC is a high-performance, polymer-modified, fiber-reinforced cement-based skimcoating and patching compound. Use Planiprep SC to skimcoat and smooth minor surface variations and defects on common substrates. Planiprep SC creates a strong, durable surface ready for almost any floor application. Its unique formulation mixes easily with water and produces an easy-to-apply patching compound. Rapid-setting Planiprep SC allows for fast-track flooring installations in 30 to 60 minutes after application, depending on thickness and environmental conditions.

Ultrabond ECO 901

Premium Adhesive for FRP Panels Ultrabond ECO 901 adhesive has been specfically formulated as a bonding agent for fiberglass reinforced plastic (FRP) panels.

Ultrabond ECO 811

Universal Carpet Tile Adhesive Ultrabond ECO 811 is a high-performance, acrylic latex adhesive designed to provide an aggressive tack for installing all types of carpet tile. Ultrabond ECO 811 provides a secure, releasable adhesive base for standard PVC-backed carpet tile as well as for non-PVC-, polyolefin-, felt- and bituminous-backed carpet tile. It can also be used to bond fiberglass-reinforced vinyl sheet flooring.

Planitex SLF

Fiber-Reinforced, Gypsum, Self-Leveling Underlayment Planitex SLF is a fiber-reinforced, gypsum-based, self-leveling underlayment with enhanced flexural strength. It resists cracking and provides an exceptionally smooth, hard surface for use in dry, interior residential and commercial areas. Planitex SLF provides an excellent substrate for a wide variety of floor coverings. Planitex SLF can also be used to cover radiant or in-floor heating systems.

Primer X

Fast-Drying, Textured Primer for Nonporous Substrates Primer X is a fast-drying, high-performance, low-VOC, water-based, acrylic primer. It is textured to enhance the performance and adhesion of self-leveling underlayments over 100%-solids, epoxy moisture barriers and other nonporous substrates.

Planiprep 4 LVT [NA]

High-Moisture-Resistant Skimcoat and Embossing Leveler Planiprep 4 LVT [NA] is a premixed, high-moisture-resistant, water-based, acrylic-resin-based skimcoat and embossing leveler.

All Video Tutorials, Webinars

MAPEI Webinar – The science of sealers

Explore the innovative technology that goes into every UltraCare bottle, unveil tips and tricks, and ensure…

UltraCare Penetrating Plus SB Stone & Porcelain Tile Sealer

UltraCare Low-Sheen Sealer & Finish

UltraCare Penetrating SB Stone, Tile & Grout Sealer

+ 6

Show products

Featured Products

UltraCare Penetrating Plus SB Stone & Porcelain Tile Sealer

UltraCare Penetrating Plus SB Stone & Porcelain Tile Sealer is a premium , natural-look, solvent-based penetrating sealer that uses VOC-exempt materials and will provide maximum protection against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed porcelain and ceramic tiles, masonry, quarry tiles and cement grout. The product can also be used as a pre-grouting sealer.

UltraCare Low-Sheen Sealer & Finish

UltraCare Low-Sheen Sealer & Finish is a one-step, water-based formula that provides a durable, low-sheen satin finish and maximum stain resistance. This product can also be used as a pre-grouting sealer. UltraCare Low-Sheen Sealer & Finish is non-yellowing and resistant to ultraviolet light.

UltraCare Penetrating SB Stone, Tile & Grout Sealer

UltraCare Penetrating SB Stone, Tile & Grout Sealer is a natural-look, solvent-based penetrating sealer that provides maximum protection against most common stains. It is safe for use on all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed porcelain and ceramic tiles, masonry, quarry tiles and cement grout. The product can also be used as a pre-grouting sealer.

UltraCare Enhancing Plus Stone Sealer

UltraCare Enhancing Plus Stone Sealer is a premium, color-enhancing penetrating sealer that enhances the natural colors of stone and provides maximum protection against most common stains. It is safe for use on all interior and exterior natural-stone surfaces, such as marble, limestone, sandstone, slate, granite, travertine and cementitious grout. The product can also be used as a pre-grouting sealer.

UltraCare High-Gloss Sealer & Finish

UltraCare High-Gloss Sealer & Finish is a one-step, water-based formula that provides a durable high-gloss finish and maximum stain resistance. This product can also be used as a pre-grouting sealer. For interior use only, UltraCare High-Gloss Sealer & Finish is non-yellowing and resistant to ultraviolet light.

UltraCare Enhancing Stone Sealer

UltraCare Enhancing Stone Sealer is an economical, color-enhancing penetrating sealer that enhances the natural colors of stone and provides protection against most common stains. It is safe for use on all interior and exterior natural-stone surfaces such as marble, limestone, sandstone, slate, granite, travertine and cementitious grout. The product can also be used as a pre-grouting sealer.

UltraCare Grout Sealer

UltraCare Grout Sealer is an affordable, water-based penetrating sealer that will provide protection against most common stains for sanded and non-sanded cementitious grout joints. It can also be used as a pre-grouting sealer.

UltraCare Penetrating Plus Stone, Tile & Grout Sealer

UltraCare Penetrating Plus Stone, Tile & Grout Sealer is a premium, natural-look, water-based penetrating sealer that provides maximum protection against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed ceramic tile, masonry and grout. The product can also be used as a pre-grouting sealer.

UltraCare Penetrating Stone, Tile & Grout Sealer

UltraCare Penetrating Stone, Tile & Grout Sealer is an economical, natural-look, water-based penetrating sealer that protects against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed ceramic tile, masonry and cement grout. The product contains no silicones and can also be used as a pre-grouting sealer.

Webinars, All Video Tutorials

MAPEI Webinar – MAPEI’s Ultratop Loft cementitious micro-topping systems

Resurfacing interior concrete floors, walls and even ceilings with Ultratop Loft micro-topping systems…

Mapefloor Finish 58 W [NA]

Primer SN [NA]

Mapenet 150 [NA]

+ 7

Show products

Featured Products

Mapefloor Finish 58 W [NA]

Primer SN [NA]

Mapenet 150 [NA]

Fiberglass Mesh for Reinforcing and Improving Ultratop Loft Systems Mapenet 150 [NA] is a fiberglass, thin, strong and flexible mesh that enhances the performance of Ultratop Loft systems. When embedded in MAPEI’s Primer SN [NA] or Primer SN Fast epoxy primer, Mapenet 150 [NA] can be used in horizontal application of the system. Mapenet 150 [NA] can be also used into Ultratop Loft F [NA] or Ultratop Loft W [NA] in vertical application of the system.

Ultratop Loft F [NA]

Ultratop Loft W [NA]

Ultratop Easycolor [NA]

Concentrated, Liquid Pigment Solution for Coloring Ultratop Loft Micro-Topping Ultratop Easycolor [NA] is a one-component, concentrated, liquid pigment solution available in a broad range of hues. It is specially formulated to color MAPEI’s trowel-applied, cementitious micro-toppings Ultratop Loft F [NA] and Ultratop Loft W [NA].

Primer Grip White [NA]

Low-VOC, Synthetic, Resin-Based Primer for Ultratop® Loft Toppings Primer Grip White [NA] is a ready-to-use, low-VOC, synthetic resin-based primer with bond-promoting silica aggregates suspended in dispersion. It enhances the performance and adhesion of MAPEI’s Ultratop Loft toppings to existing ceramic tile and other difficult-to-bond-to substrates in vertical applications. Suitable for a wide variety of substrates, Primer Grip White [NA] combines excellent versatility with an easy, low-odor application.

Mapefloor Finish 630 [NA]

Ultratop Base Coat [NA]

Primer LT [NA]

Water-Based, Acrylic Primer for Ultratop Loft Toppings Primer LT [NA] is a low-VOC, water-based acrylic primer that enhances the performance and adhesion between layers of Ultratop Loft toppings for walls and floors. Primer LT [NA] combines excellent versatility with easy, low-odor applications for indoor use.

All Video Tutorials, Webinars

MAPEI Webinar – MAPEI’s Mapeguard UM 35: Reshaping the industry

Learn about the advanced technology – including superior crack isolation, uncoupling, and moisture and vapor…

Mapeguard UM 35 [NA]

Mapeguard PIC

Mapeguard POC

+ 1

Show products

Featured Products

Mapeguard UM 35 [NA]

Mapeguard ® UM 35 [NA] is an uncoupling, crack-isolation, waterproofing and vapor-management membrane made from high-density polyethylene (HDPE) with a rough surface and polypropylene fabric backing. Mapeguard UM 35 [NA] is designed for installing ceramic and stone tile, including over existing non- cushioned resilient flooring, ceramic tile and stone tile. It is designed to perform over challenging substrates, such as young concrete and single-layer 3/4" (19 mm) plywood subfloors with joist spacing of up to 19.2" (49 cm) on center.

Mapeguard PIC

Pre-Formed Inside Corners Mapeguard PIC is a thin, flexible, alkali-resistant, polyethylene membrane coated on both sides with a nonwoven polypropylene fabric. It offers a fast and easy way to seal inside corners in wet areas where walls and floors meet, providing waterproofing and vapor management protection when combined with Mapeguard WP 200 waterproofing membrane for ceramic tile and stone.

Mapeguard POC

Pre-Formed Outside Corners Mapeguard POC is a thin, flexible, alkali-resistant, polyethylene membrane coated on both sides with a nonwoven polypropylene fabric. It offers a fast and easy way to seal outside corners, curbs or return walls in wet areas where walls/curbs and floors meet, providing waterproofing and vapor management protection when combined with Mapeguard WP 200 waterproofing membrane for ceramic tile and stone.

Mapeguard WP ST

Waterproofing Sealing Tape for Mapeguard WP 200 Mapeguard WP ST is a fast and easy way to cover seams and wall upturns to provide waterproofing and vapor management protection when installing Mapeguard WP 200 waterproofing sheet membrane for ceramic tile and stone.

All Video Tutorials, Webinars

MAPEI Webinar: Refurbishing existing resilient flooring

Tired-looking vinyl flooring? Resurface it with the Ultracoat ReNewIt system.

Mapecoat 4 LVT [NA]

Ultracoat HT 2K

Ultracoat ReNewIt Remover

+ 2

Show products

Featured Products

Mapecoat 4 LVT [NA]

Ultracoat HT 2K

Ultracoat ReNewIt Remover

Ultracoat ReNewIt Primer

Ultracoat ReNewIt Cleaner

All Video Tutorials, Webinars

MAPEI Webinar – Fiber reinforced polymers: A game-changer for concrete longevity and performance

Fiber reinforced polymers (FRPs), which are composed of high-strength fibers that are embedded in a polymer…

Mapewrap C FIOCCO

Mapewrap G FIOCCO

MapeWrap C Bi-Ax

+ 11

Show products

Featured Products

Mapewrap C FIOCCO

Unidirectional high-strength carbon fiber, glass fiber or basalt fiber cord for impregnation with MapeWrap 21 to make “structural connections” Structural and functional restoration of concrete elements and masonry, including those of historical interest, which have been damaged by inclement weather and natural causes. MapeWrap C FIOCCO , MapeWrap G FIOCCO and MapeWrap B FIOCCO are used as “structural connection” placed on the inside of old masonry to guarantee a better connection between the substrate (concrete, stone, bricks, wood, etc.) and the strengthening products with FRP and FRCM technology.

Mapewrap G FIOCCO

MapeWrap C Bi-Ax

Maperod G

Maperod C

Carboplate E 170

MapeWrap G Uni-Ax

MapeWrap 31 T [NA]

Medium-Viscosity, 100%-Solids Epoxy Resin for Dry-Layup Impregnation of MapeWrap Fabrics MapeWrap 31 T [NA] is a 100%-solids, moisture-tolerant, medium-viscosity epoxy resin used to encapsulate the MapeWrap composite system fabrics using the dry layup method. MapeWrap 31 T [NA] was specially developed to saturate and encapsulate both carbon and glass fiber fabrics and to cure to a high-performance FRP laminate. Once cured, the laminate provides additional strength to appropriate structural elements.

MapeWrap 21 TG

Low-Viscosity, 100%-Solids Epoxy Resin for Mechanical Saturation of MapeWrap Fabrics MapeWrap 21 TG is a 100%-solids, moisture-tolerant, low-viscosity epoxy resin with an extended working time used to encapsulate the MapeWrap composite system fabrics via the wet layup technique. MapeWrap 21 TG was specially developed to saturate and encapsulate both carbon and glass fiber fabrics by way of mechanical saturation and to cure to a high-performance laminate. Once cured, the laminate provides additional strength to appropriate structural elements.

MapeWrap 31

Medium-Viscosity, 100%-Solids Epoxy Resin for Impregnation of MapeWrap Fabrics MapeWrap 31 is a 100%-solids, moisture-tolerant, medium-viscosity, epoxy resin for impregnating MapeWrap composite system fabrics by a dry layup method. MapeWrap 31 was specially developed to saturate and encapsulate carbon and glass fiber fabrics and to cure to a high-performance laminate. Once cured, MapeWrap 31 provides high mechanical strength properties.

MapeWrap 21

Low-Viscosity, 100%-Solids, Epoxy Resin for Impregnation of MapeWrap Fabrics MapeWrap 21 is a 100%-solids, moisture-tolerant, low-viscosity, epoxy resin used to encapsulate the MapeWrap composite system fabrics. MapeWrap 21 was specially developed to saturate and encapsulate carbon and glass fiber fabrics and to cure to a high-performance laminate. Once cured, the laminate provides additional strength to appropriate structural elements.

MapeWrap 12

Structural Epoxy Putty Adhesive for Use with Structural Strengthening Systems in Warm Climates MapeWrap 12 is a two-component, 100%-solids, moisture-tolerant, structural epoxy used as an adhesive for the Carboplate composite system in warm climates. MapeWrap 12 is also used for leveling uneven concrete or masonry surfaces before application of MapeWrap fabrics or Carboplate and Maperod C laminates.

MapeWrap Primer 1

Low-Viscosity, 100%-Solids, Epoxy Resin Primer for the MapeWrap Composite System MapeWrap Primer 1 is a 100%-solids, moisture-tolerant, low-viscosity, two-component, epoxy resin that is used as a seal coat for consolidating and priming concrete substrates. As the first component of the MapeWrap composite system, MapeWrap Primer 1 penetrates cementitious pore structures and provides a high bond for the other system components.

MapeWrap 11

Structural Epoxy Putty Adhesive for Use with Structural Strengthening Systems MapeWrap 11 is a two-component, 100%-solids, moisture-tolerant, structural epoxy used as an adhesive for the Carboplate composite system in horizontal, vertical and overhead applications. MapeWrap 11 is also used for leveling uneven concrete or masonry surfaces before application of MapeWrap fabrics or Carboplate and Maperod C laminates.

All Video Tutorials, Webinars

MAPEI Webinar – Beat the heat: A coatings response to climate change

Can wall coatings reflect heat? Are cool wall coatings as good as or better than regular coatings?

Elastocolor Coat DOT-MOT

Mapecoat Deck S

Mapecoat Deck T

+ 6

Show products

Featured Products

Elastocolor Coat DOT-MOT

Water-Based, High-Build, 100%-Acrylic Coating Elastocolor Coat DOT-MOT is specially formulated to meet the surface coating needs of the bridge and highway construction market, for coating new and previously painted concrete structures. It exhibits superior application qualities and long-term performance on exposure to the environment.

Mapecoat Deck S

Mapecoat ™ Deck S is a water-based, urethane-modified, acrylic coating specially designed for use on new and previously coated concrete and masonry as a waterproofing sealer. Mapecoat Deck S has an attractive, low-sheen finish that creates a durable wear surface for residential and commercial indoor/outdoor floors, decks, balconies and walkways. An optional high-gloss clear coat can be used to provide additional protection and dimension for creative effects or broadcast elements. Mapecoat Deck S offers enhanced adhesion and durability to withstand pedestrian and light vehicular traffic with the convenience and ease of application of a single-component product.

Mapecoat Deck T

Mapecoat ™ Deck T i s a water-based, slip-resistant coating specially designed for use on new and previously coated concrete and masonry as a waterproofing sealer. Mapecoat Deck T creates an attractive, durable wear surface for residential and commercial indoor/outdoor decks, balconies and walkways. It offers enhanced durability to withstand pedestrian and light vehicular traffic with the convenience and easy application of a single-component product.

Elastocolor Flex

Elastocolor ® Flex is an elastomeric, high-build, water-based, 100%-acrylic coating to protect and decorate above-grade, vertical exterior concrete, masonry, stucco and EIFS systems. Elastocolor Flex is available in two textures (smooth and fine), in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility.

Elastocolor Primer AR

Water-Based, Alkali-Resistant Primer for Elastocolor Coatings Elastocolor Primer AR is a specially designed primer for use on exterior, above-grade, new and previously coated concrete and masonry surfaces. Elastocolor Primer AR will protect subsequent coatings from the damaging effects of high pH present in freshly placed cement-based products. It remains highly flexible, offers excellent filling and adhesion on prepared substrates, and is designed for compatibility with MAPEI’s Elastocolor coating systems.

Elastocolor Coat

Water-Based, High-Build, 100%-Acrylic, Waterproof Coating Elastocolor Coat is a water-based, high-build, 100%-acrylic coating designed to protect and decorate above-grade, exterior/interior vertical concrete, masonry, stucco, fiber-reinforced polymer (FRP) composites and EIFS systems. Elastocolor Coat is available in two textures (smooth and fine), in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility.

Elastocolor Primer WB

Water-Based, 100%-Acrylic Primer for Elastocolor Coatings Elastocolor Primer WB is a clear, water-based, 100%-acrylic primer for use with Elastocolor coatings. Elastocolor Primer WB improves adhesion on porous, dusting and new substrates.

Elastocolor Paint

Elastocolor ® Paint is a high-quality, water-based, 100%-acrylic coating that forms a protective film for use on above-grade, exterior/interior concrete, masonry, stucco, fiber-reinforced polymer (FRP) composites and EIFS systems. Elastocolor Paint is available in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility.

Elastocolor Texture

Elastocolor ® Texture is a specially designed coating for use on exterior, above-grade, new and previously coated concrete and masonry surfaces. Elastocolor Texture ’s unique blend of aggregates produces an attractive, high-build, textured finish. It is ideal for use on restoration projects to reduce the appearance of surface imperfections and repairs or wherever a uniform textured finish is desired. Elastocolor Texture remains highly flexible and offers excellent filling properties and adhesion to prepared substrates.

All Video Tutorials, Webinars

MAPEI Webinar: Choosing the best adhesive for your synthetic-turf installation

MAPEI’s synthetic-turf installation product line for sport facilities and landscapes

Ultrabond Turf HMA

Ultrabond Turf Glue Box

Ultrabond Turf Epoxy Repair

+ 9

Show products

Featured Products

Ultrabond Turf HMA

Hot-Melt Adhesive for Synthetic Turf Ultrabond Turf HMA is a hot-melt adhesive specifically formulated for the installation of synthetic turf using industrial hot-melt applicator machines. Ultrabond Turf HMA offers a permanent, fast and efficient method for seaming, inlay and quick repairs of synthetic turf installation in a variety of weather conditions.

Ultrabond Turf Glue Box

Ultrabond Turf Glue Box is the perfect application tool for seaming together synthetic turf sports fields using a MAPEI synthetic turf adhesive ( Ultrabond Turf PU 1K , Ultrabond Turf PU 2K or Ultrabond Turf MS ) along with Ultrabond Turf Tape . Ultrabond Turf Glue Box includes two sets of trowel notches – 1/4" (6 mm) square-notch and 5/32" x 3/16" (4 x 4.5 mm) sawtooth – which are ideal for the recommended adhesive coverage. Featuring a double-roller design for faster changing of seam tape rolls, this tool has components made from HDPE for easy cleanup.

Ultrabond Turf Epoxy Repair

Premium, Fast-Setting, Epoxy Repair Adhesive for Synthetic Turf Ultrabond Turf Epoxy Repair is a fast-setting, two-component, 100%-epoxy adhesive designed for high-strength, fast repairs of synthetic turf used in athletic applications. Ultrabond Turf Epoxy Repair comes in dual-component cartridges with static mixer tips for efficient installations, eliminating the need to mix the two components by hand. The adhesive cures within 2 hours under normal conditions to a high bond strength that exceeds FIFA requirements. Ultrabond Turf Epoxy Repair provides an easy synthetic turf repair that is durable and permanent.

Ultrabond Turf MS

Premium, Hybrid, Synthetic Turf Adhesive Ultrabond Turf MS is a high-tack, fast-setting, one-component, modified-silane hybrid adhesive designed for installation of high-performance synthetic sports turf. Ultrabond Turf MS meets FIFA bond requirements and is suitable for installation in most weather conditions. Ultrabond Turf MS is colored green to blend in with most synthetic turf products.

Ultrabond Turf PU 2K

Professional, Two-Component, Fast-Set, Urethane Turf Seam Adhesive Ultrabond Turf PU 2K is a high-performance, two-component, fast-set, urethane adhesive designed for the high-performance seaming and direct bonding of synthetic turf used in athletic and landscape applications. Ultrabond Turf PU 2K is particularly suited for use in areas of low ambient relative humidity and in cool temperatures. Ultrabond Turf PU 2K is colored green to blend in with most synthetic turf products and cures within 2 to 4 hours to a tough, durable bond. Ultrabond Turf PU 2K provides seam strengths that exceed FIFA standards.

Ultrabond Landscape Turf CG

Commercial-Grade, Landscape Turf Adhesive Ultrabond Landscape Turf CG is a commercial-grade adhesive ideal for indoor and outdoor landscaping synthetic turf installations. Ultrabond Landscape Turf CG has excellent all-weather resistance with superior bond strength and can be used for full spread and seaming installations.

Ultrabond Landscape Tape

Seam Tape for Landscaping Synthetic Turf Ultrabond Landscape Tape is a low-density, PET-based, spun-bonded, nonwoven fabric tape designed specifically to work with Ultrabond Landscape Turf CG adhesive for seaming landscaping synthetic turf. Ultrabond Landscape Tape is waterproof and provides excellent tensile strength and tear resistance. Ultrabond Landscape Tape is the ideal seaming base for installations of all landscaping synthetic turf.

Ultrabond Turf PU 1K-LV

Low-Viscosity, Fast-Setting, Urethane Adhesive for Turf Installation Ultrabond Turf PU 1K-LV is a fast-setting, moisture-curing, polyurethane adhesive specifically designed for full glue-down applications with smooth-backed synthetic turf, such as for batting cages and lacrosse fields. The low-viscosity formula can be flat-troweled or sprayed via an airless pump sprayer. Ultrabond Turf PU 1K-LV is also suitable for repairs, curbs/edging and detail work.

Ultrabond Turf PU 2K Accelerator

Admixture for Ultrabond Turf PU 2K Ultrabond Turf PU 2K Accelerator is an additive designed for Ultrabond Turf PU 2K to allow for quicker setting and curing times. Ultrabond Turf PU 2K Accelerator is ideal for temperatures below 50°F (10°C) to allow Ultrabond Turf PU 2K to achieve standard curing rates. At a wide range of ambient temperatures, the curing time can be shortened to allow for faster installs and repairs.

Ultrabond Turf Tape

Premium Turf Seam Tape Ultrabond Turf Tape is a PET-based, spun-bonded, nonwoven fabric tape designed specifically to work with MAPEI turf adhesives for seaming synthetic turf. Ultrabond Turf Tape is waterproof and provides superior tensile strength and tear resistance, which are vital for installations of professional athletic playing fields. It is also perfectly suited as a seaming base for other synthetic turf applications, including installations of residential landscaping, playgrounds and golf courses.

Ultrabond Turf PU 1K-HV

High-Viscosity, Urethane Adhesive for Turf Seams Ultrabond Turf PU 1K-HV is a high-viscosity, moisture-curing, one-component, urethane adhesive specifically designed for bonding of synthetic turf in high-performance sports installations. Offering excellent weather resistance, Ultrabond Turf PU 1K-HV can be used in interior and exterior applications. It meets FIFA requirements for bond strength in sports-turf applications.

Ultrabond Turf PU 1K

Premium, Fast-Setting, Urethane Adhesive for Turf Seams Ultrabond Turf PU 1K is a fast-setting, moisture-curing, one-component, urethane adhesive specifically designed for bonding of synthetic turf in high-performance sports installations. Offering excellent weather resistance, Ultrabond Turf PU 1K can be used in interior and exterior applications. It meets FIFA requirements for bond strength in sports-turf applications.

All Video Tutorials, Webinars

MAPEI Webinar – Mapecoat TNS System: Empowering sport-flooring contractors

Replacing or resurfacing a tennis or pickleball court? Whether for aesthetics or comfort, MAPEI’s Mapecoat…

Webinars, All Video Tutorials

MAPEI Webinar – Mapesoil: Solving the drainage-stability paradox for sports surfaces

When installing synthetic turf on your putting green, how do you handle the drainage? Don’t worry. MAPEI has…

Mapesoil SR

Mapesoil 100

Show products

Featured Products

Mapesoil SR

Professional, Hydraulic Binder for Sub-Base Repair of Sports Surfaces Mapesoil SR is a hydraulic binder used to repair sub-bases with vertical and horizontal drainage systems.

Mapesoil 100

High-Performance, Fiber-Reinforced, Powdered Stabilizing Agent for Sports Surface Sub-Bases Mapesoil 100 is a hydraulic, high-performance, fiber-reinforced, powdered stabilizing agent used to treat and consolidate soil and recycled or raw aggregates, such as naturally graded soil.

All Video Tutorials, Webinars

Mapecontact SRT – A new and novel approach for wood flooring

Does installing wood flooring using tape sound too good to be true? Not with moisture-resistant Mapecontact…

Mapecontact SRT

Show products

Featured Products

Mapecontact SRT

Sound-Reduction, Moisture-Resistant Tape for Resilient and Wood Flooring Installation Mapecontact SRT is a double-sided, foam-core, dry-film tape for rapidly and permanently installing solid vinyl sheet, vinyl tile and vinyl plank flooring, as well as prefinished engineered and solid wood. Providing sound reduction for multi-family living, it has also been specifically designed to instant bond and instant utilization for residential and commercial floor installations. Mapecontact SRT is unaffected by high moisture conditions in concrete and can be installed without moisture testing. Plus, it provides subfloor moisture protection for wood and bamboo flooring.

All Video Tutorials, Webinars

MAPEI Webinar – Best Practices for a Gap-Free LVT Installation

Calling all installers! Our manufacturer’s Webinar will make you a gap-free LVT flooring pro.

Ultrabond ECO 379

Ultrabond ECO 399

Ultrabond ECO 350

+ 6

Show products

Featured Products

Ultrabond ECO 379

Ultrabond ECO 399

Ultrabond ECO 350

Mapecontact MRT

Moisture-Resistant Tape for Resilient Flooring Installation Mapecontact MRT is a double-sided, moisture-resistant tape for the rapid and permanent installation of a wide variety of resilient flooring types. It has been specifically designed to provide instant bond and instant utilization for residential and commercial floor installations. Mapecontact MRT is unaffected by high moisture conditions in concrete and can be installed without moisture testing.

Ultrabond ECO 373

Ultrabond ECO 360

Ultrabond G21

Ultrabond G19

Ultrabond ECO 811

All Video Tutorials, Featured Videos, Webinars

MAPEI Webinar – The Science of the Concrete Surface

Moisture in your concrete? What is the goo under the flooring? It could be the result of osmosis,…

All Video Tutorials, Featured Videos, Webinars

MAPEI Webinar – Cold-fluid-applied waterproofing membranes (MAP061)

Looking for a roller-applied, no odor, no VOCs waterproofing solution? Look no further than MAPEI's Planiseal…

Mapeflex P1 FT

Idrostop B25

Planiseal CR1

+ 4

Show products

Featured Products

Mapeflex P1 FT

One-Component, Nonsag, Elastomeric Polyurethane Sealant Mapeflex P1 FT is a high-performance, one-component, fast-track, elastomeric, moisture-cured, polyurethane sealant and adhesive. Mapeflex P1 FT offers excellent adhesion to most surfaces, superior gunning and tooling, and excellent flexibility for moving joints.

Idrostop B25

Bentonite-Based, Hydrophilic, Expandable, Flexible Rubber Waterstop Strip for Watertight Construction Idrostop B25 is a waterstop used to produce watertight construction joints in civil, industrial and hydraulic construction. Idrostop B25 is composed of a mix of natural sodium bentonite and polymers that give the product exceptional properties of compactness, flexibility and stability. The material is produced according to a formula developed in MAPEI’s own research and development laboratories. Idrostop B25 ’s expanding process takes place in a controlled, gradual and uniform way without the risk of altering the balance of the mix.

Planiseal CR1

Mapedrain 35

High-Strength, High-Flow, Prefabricated Drainage Composite with Woven Filter Fabric and Protective Film Mapedrain 35 is a high-strength, three-dimensional drainage composite. It consists of a woven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core. Mapedrain 35 ’s woven, monofilament fabric withstands high abrasion from applied overburden and prevents intrusion into the drainage core due to its low elongation characteristics. As such, the woven fabric is better suited to receive direct poured concrete than nonwoven geotextile fabrics. Mapedrain 35 also has a polymeric protective film on the back side to provide additional protection to waterproofing membranes.

MAPEI LMR Fabric

Reinforcing Fabric for Liquid Waterproofing Membranes MAPEI LMR Fabric is a spunbond, nonwoven polyester fabric used as a reinforcement for liquid-applied waterproofing membranes. When embedded into a liquid-applied waterproofing membrane, it will add strength and durability to the overall system.

Mapeflex P2 NS

Mapeflex ® P2 NS is a two-component, non-sag, polyurethane sealant that meets the requirements of ASTM C920.

Mapedrain 25

High-Strength, High-Flow, Prefabricated Drainage Composite with Protective Film Mapedrain 25 is a high-strength, three-dimensional drainage composite. It consists of a nonwoven filter fabric bonded to individual dimples of the molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles which might clog the core. Mapedrain 25 also has a polymeric protective film on the back side to provide additional protection to waterproofing membranes.

All Video Tutorials, Webinars

MAPEI Webinar – Updates on MAPEI’s Self-Leveling Underlayments

Do you use self-levelers for concrete floors? Get the latest updates on MAPEI’s self-leveling underlayments…

Novoplan HFL

Novoplan DPL

Mapesand Coarse

+ 17

Show products

Featured Products

Novoplan HFL

Novoplan DPL

Mapesand Coarse

Calibrated, 16/30 Mesh Sand Mapesand Coarse is a calibrated, washed and oven-dried, 16/30 mesh silica sand for use with resin and epoxy primers to create texture, which is necessary for the primer to bond with self-leveling and topping compounds.

Mapesand Fine

Calibrated, 20/40 Mesh Sand Mapesand Fine is a calibrated, washed and oven-dried, 20/40 mesh silica sand for use as an extender for Planitex SL gypsum self-leveling underlayment, and to improve the bond of resin and epoxy primers with self-leveling and topping compounds.

Planiseal MSP

Ultraplan Extreme 2

Ultraplan Lite

Novoplan Easy Plus

Novoplan 2 Plus

Professional, Self-Leveling Underlayment Novoplan 2 Plus is a high-strength, self-leveling, cement-based underlayment and repair mix for interior concrete and engineer-approved floors.

Ultraplan M20 Plus

Ultraplan Easy

Primer T

Primer E

Primer CE

Primer L

Primer WE

Ultraplan 1 Plus

ECO Prim Grip

Planitex SLF

Primer X

Webinars, All Video Tutorials

MAPEI Webinar – Keraflex Mortars: Simplification and Consolidation

MAPEI’s Keraflex family of mortars covers most jobsite needs, allowing contractors and distributors to…

Keraflex RS

Keraflex Super

Keraflex Plus

Show products

Featured Products

Keraflex RS

Professional, Rapid-Setting, Extra Smooth, Large-and-Heavy-Tile Mortar with Polymer Keraflex RS is a fast-setting, highly versatile, large-and-heavy-tile mortar and thin-set mortar for tile and stone installation on floors, walls and countertops. It is formulated as nonsag for walls and nonslump for floors, allowing tiles to be grouted in as little as 3 to 4 hours after installation. Keraflex RS is a polymer-modified, smooth and creamy mortar formulated with Easy Glide Technology for ease of application and offers excellent adhesion to substrates and tile. It can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.

Keraflex Super

Keraflex ® Super is a highly versatile, nonsag/nonslump, large-and-heavy-tile mortar and thin-set mortar for tile and stone for installations on floors, walls and countertops. This polymer-modified mortar has a high content of a unique dry polymer, resulting in excellent adhesion to the substrate and tile, with enhanced resistance to freeze/thaw environments. This product features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions. It is formulated with Easy Glide Technology ™ for ease of application and with a consistency that allows adjustability when used with lippage control systems. Keraflex Super can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.

Keraflex Plus

Professional, Extra Smooth, Large-and-Heavy-Tile Mortar with Polymer Keraflex Plus is a highly versatile, nonsag/nonslump, large-and-heavy-tile mortar and thin-set mortar for tile and stone installations on floors, walls and countertops. This polymer-modified mortar is formulated with Easy Glide Technology for ease of application and offers excellent adhesion to substrates and tile. It can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.

All Video Tutorials, Webinars

MAPEI Webinar – MAPEI073: Selecting Sustainable Products for Green Building Certifications

Which sustainable product provides the most credits? Which green building certification provides the best fit…

Webinars, All Video Tutorials

MAPEI Webinar – Installation, Finishing and Maintenance for Wood Floors

Installing wood flooring? By the end of this Webinar, you will learn best wood-floor installation practices…

Ultracoat Easy

Ultracoat Premium Base

Ultracoat Toning Base

+ 25

Show products

Featured Products

Ultracoat Easy

Ultracoat Premium Base

Ultracoat Toning Base

Ultracoat HT 2K

Ultracoat Aqua Plus

Ultracoat Easy Plus

Ultrabond ECO 977

Ultrabond ECO 907

Mapesonic RM

Premium, Sound-Reduction Rubber Membrane Mapesonic RM is a high-performance, acoustic underlayment designed to reduce ambient and impact sound transmissions in installations of ceramic and porcelain tile, natural stone, wood flooring, luxury vinyl tile (LVT), luxury vinyl plank (LVP), sheet vinyl and carpet tile. Mapesonic RM is ideal for applications in apartments, condominiums, college dormitories, classrooms and office buildings.

Ultracoat Gym Pro

Ultracoat Gym

Planiseal MSP

Ultracoat ReNewIt Remover

Ultracoat ReNewIt Primer

Ultrabond ECO 983

Ultracoat ReNewIt Cleaner

Ultracoat Clean WPM

Low-Gloss Cleaner and Polish for Wood Floors Ultracoat Clean WPM is a concentrated product that may be diluted with clean water for regular maintenance or used at full strength for greater protection and appearance. It has been specially developed for the maintenance of interior residential and commercial wooden floors treated with Ultracoat wood-floor finishes. Ultracoat Clean WPM gives the surface of floors a low-gloss appearance and also increases the protection against wear by forming a water-repellent film.

Ultracoat Clean Polish

Cleaner and Polish for Wood Floors Ultracoat Clean Polish is a concentrated product that may be diluted with clean water for regular maintenance or used at full strength for greater protection and appearance. It has been specially developed for the maintenance of interior residential and commercial wooden floors treated with Ultracoat wood-floor finishes. Ultracoat Clean Polish gives floor surfaces a bright, shiny appearance and also increases protection against wear by forming a water-repellent film.

Ultracoat Polish Remover

Concentrated Polish Remover for Wood Floors Ultracoat Polish Remover is a concentrated solution specifically formulated for the removal of wax-based or polymer-based wood-floor polishes.

Ultracoat Universal Cleaner

Concentrated Cleaner for Wood Floors Ultracoat Universal Cleaner is a concentrated detergent specifically formulated for cleaning wood floors coated with either water-based or oil-based finishes.

Planiseal VS Fast

Ultrabond ECO 985

Ultrabond ECO 995

Planiseal VS

Ultrabond ECO 980

Ultrabond ECO 975

Ultrabond Urethane Cleaner

Ultracoat Universal Base

Webinars, All Video Tutorials

MAPEI Webinar – MAPEI’s Ultratop Decorative Topping Solutions

Strong, lasting, self-leveling concrete toppings that replicate the look and durability of terrazzo – as well…

Epojet LV [NA]

Epojet [NA]

Show products

Featured Products

Epojet LV [NA]

Epojet [NA]

Epojet ™ [NA] is a high-strength, two-component, 100%-solids, low-viscosity, epoxy resin for pressure injection and sealing of cracks in structural concrete, masonry and wood.

Webinars, All Video Tutorials

MAPEI Webinar – The Chemistry of Tile Grouts, Caulks and Sealers

Learn how simple chemistry can help raise your grout installations from ordinary to amazing.

Mapesil T Plus

Ultracolor Plus Max

Kerapoxy

+ 8

Show products

Featured Products

Mapesil T Plus

Mapesil ® T Plus is a professional-grade, 100%-silicone sealant with enhanced adhesion for use on multiple substrates. This product is specifically formulated for heavy traffic and expansion/movement joints exceeding both ASTM and ANSI standards.

Ultracolor Plus Max

High-Performance, Rapid-Setting Grout with Maximized Color Depth and Color Consistency Ultracolor Plus Max is an ultra premium, fast-setting, polymer-modified, nonshrinking grout that offers rich and vibrant colors with maximized color depth and color consistency. This fine-aggregate grout can be used for joint widths from 1/16" to 3/4" (1.5 mm to 19 mm). Ultracolor Plus Max includes DropEffect technology for reduced surface absorption, helping to repel water, dirt and grime from penetrating grout joints. It is also specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT) to provide advantages over traditional grout, such as eliminating efflorescence and increasing stain resistance.

Kerapoxy

Premium, Epoxy Grout and Mortar Kerapoxy is a premium-grade, water-cleanable, 100%-solids, high-strength, chemical-resistant, nonsagging, epoxy grout and mortar that offers excellent stain and chemical resistance. This versatile product is ideal for a wide range of projects, from countertops to shopping malls to airport terminals.

MAPEI Flexcolor 3D

Ready-to-Use, Translucent Grout with an “Iridescent Effect” Finish MAPEI Flexcolor 3D is a professional-grade, ready-to-use (RTU) translucent specialty grout with an “iridescent effect” finish. It is offered in 10 designer colors with translucent characteristics that not only reflect but also refract light. This allows the grout to transition in color to complement the tile color. The “translucent effect” is most noticeable with the color Crystal Moon (#201), while the other nine colors exhibit a more pronounced “iridescent effect.” MAPEI Flexcolor 3D is also formulated for commercial and residential interior installations of porcelain, ceramic, glass and natural-stone tiles. Plus, the dense surface structure of the grout helps to prevent water-based stains on the grout surface. MAPEI Flexcolor 3D is formulated with the latest innovation in recycled glass-bead aggregate, which ensures color consistency, ease of cleanability and improved workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation. Comparison testing of MAPEI Flexcolor 3D versus traditional Portland-cement grout has verified that MAPEI Flexcolor 3D requires 65% less time to install than powder grouts.

Kerapoxy IEG CQ

100%-Solids, Industrial-Grade, Epoxy Grout with Color-Coated Quartz Kerapoxy IEG CQ is a water-cleanable, 100%-solids, epoxy grout with high chemical and stain resistance. It is a nonshrinking, nonsagging, fast-curing, efflorescence-free grout. Color-coated quartz dramatically improves its cleanability, so that Kerapoxy IEG CQ leaves very little film residue during cleanup of excess grout with a grout float. The color-coated quartz also eliminates pigment bleed, so tiles are not stained during installation. This grout is perfectly suited for use in commercial kitchens, meat packing houses, and any commercial and institutional floors that require daily cleaning with enzymatic cleaners. Kerapoxy IEG CQ is ideal for applications where high-strength, mold- and mildew-resistant grout joints are required. In addition, it has high temperature resistance and can be steam-cleaned.

Keracaulk U

Premium, Unsanded Siliconized Acrylic Caulk Keracaulk U is a premium-grade, unsanded, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match all of MAPEI’s grout colors.

Keracaulk S

Premium, Sanded Siliconized Acrylic Caulk Keracaulk S is a premium-grade, sanded, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match all of MAPEI’s grout colors.

Keracolor S Sanded Grout

Premium Sanded Grout with Polymer Keracolor S Sanded Grout is a premium-grade, pre-blended, polymer-modified sanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/8" to 5/8" (3 to 16 mm).

Keracolor U Unsanded Grout

Premium Unsanded Grout with Polymer Keracolor U Unsanded Grout is a premium-grade, preblended, polymer-modified unsanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/16" to 1/8" (1.5 to 3 mm).

MAPEI Flexcolor Design

Professional-Grade, Ready-to-Use Specialty Grout with Personalized Computer Color-Matching MAPEI Flexcolor Design is a professional-grade, ready-to-use (RTU) specialty grout that allows you to “design your color,” any color. MAPEI Flexcolor Design is formulated for commercial and residential interior installations of porcelain, ceramic, glass and natural-stone tiles. Plus, the dense surface structure of the grout helps to prevent water-based stains on the grout surface. MAPEI Flexcolor Design is formulated with the latest innovation in recycled glass-bead aggregate that enhances cleanability and improves workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation. This product is exclusively for National Brand Accounts and Commercial Projects. For complete information on samples and ordering, contact your local MAPEI architectural representative.

Ultracolor Plus FA

Ultracolor ® Plus FA – with DropEffect ™ technology and CO 2 emissions fully offset in the product's life cycle – is an ultra premium, fine-aggregate, fast-setting, polymer-modified, color-consistent, nonshrinking, efflorescence-free grout for joint widths from 1/16" to 3/4" (1.5 to 19 mm). DropEffect reduces surface absorption to help repel water, dirt and grime from penetrating grout joints. Ultracolor Plus FA is specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT ™ ) to eliminate common problems such as color consistency and efflorescence. Along with offering higher polymer content, HCT reduces absorption and increases stain resistance when compared with standard-performance cement grouts.

Webinars, All Video Tutorials

MAPEI Webinar – Adhesive Selection and Installation for LVT

There are a wide variety of adhesives on the market, but which ones work best when installing luxury vinyl…

Ultrabond ECO 399

Ultrabond ECO 350

Mapecontact MRT

+ 5

Show products

Featured Products

Ultrabond ECO 399

Ultrabond ECO 350

Mapecontact MRT

Ultrabond ECO 373

Ultrabond ECO 360

Ultrabond G21

Ultrabond G19

Ultrabond ECO 811

Webinars, All Video Tutorials

MAPEI Webinar – Past, Present and Future of Resin-Based Coatings for Ships

Floor coatings for ships must withstand major abuse and they must provide incredible corrosion protection,…

Mapedeck Litescreed

Mapedeck Teak Design

Mapedeck Design

+ 7

Show products

Featured Products

Mapedeck Litescreed

Self-Leveling, Lightweight, Self-Extinguishing, Polyurethane-Based Underlayment Mapedeck Litescreed is a two-component, lightweight, self-extinguishing, polyurethane-resin-based self-leveling underlayment used to smooth and level interior and external decks before the installation of resin flooring systems and other approved floor coverings.

Mapedeck Teak Design

Self-Leveling, Polyurethane Resin for Forming Teak-Effect Flooring Mapedeck Teak Design is a two-component, aliphatic polyurethane-resin-based, self-leveling coating used to form a seamless teak-effect finish on internal and external decks.

Mapedeck Design

Self-Leveling, Polyurethane, Seamless Flooring Resin Mapedeck Design is a two-component, aliphatic, polyurethane-resin-based, self-leveling coating used to form a seamless floor on internal and external decks.

Mapedeck Finish 100 TS

Two-Component, Aliphatic, Matte-Finish, Polyurethane Finishes Mapedeck Finish 100 , Mapedeck Finish 100 TS , Mapedeck Finish 111 R and Mapedeck Finish 111 TSR are two-component, aliphatic, matte-finish, polyurethane dispersion finishes. Depending on the product, they are available in NCS and RAL custom colors, transparent and anti-skid finishes. Mapedeck finishes form a tough abrasion-resistant, UV-resistant, non-yellowing, and easyto-clean finish over properly prepared surfaces.

Mapedeck Finish 100

Mapedeck Finish 111 R

Mapedeck Primer 200

Bonding Agent for Polyurethane-Based Systems Mapedeck Primer 200 is a bonding agent that creates an adhesion-promoting layer between the substrate and polyurethane-based products and systems.

Mapedeck Finish 111 TSR

Mapecoat Guard 100

Multipurpose Anti-Corrosion Epoxy Coating and Primer for Internal and External Ship Decks Mapecoat Guard 100 is a two-component, quick-drying multipurpose anticorrosion coating and bonding agent for use on metal substrates and as an intermediate coat on other types of primed surfaces.

Mapedeck Eposcreed Lite

Lightweight, Epoxy-Based Leveler for Interior and External Ship Decks Mapedeck Eposcreed Lite is a lightweight, epoxy-based leveling compound used to smooth and level interior and external decks before the installation of flooring.

All Video Tutorials, Webinars

MAPEI / Structures magazine – Strengthening Concrete Bridge Structures with Fiber-Reinforced Polymers (FRPs)

Using fiber-reinforced polymers to strengthen concrete structures is an effective and efficient method of…

MapeWrap G Uni-Ax

MapeWrap 31 T [NA]

MapeWrap 21 TG

+ 5

Show products

Featured Products

MapeWrap G Uni-Ax

MapeWrap 31 T [NA]

MapeWrap 21 TG

MapeWrap 31

MapeWrap 21

MapeWrap Primer 1

MapeWrap 11

MapeWrap 12

Webinars, All Video Tutorials

MAPEI and Roads & Bridges Webinar – Corrosion Mitigation of Traditionally Reinforced Concrete Structures

Learn how to how to mitigate concrete damage – and keep roads and bridges open during structural…

Mapefer 1K [NA]

Mapefloor Finish 415 NA

Microsilica

+ 6

Show products

Featured Products

Mapefer 1K [NA]

Mapefloor Finish 415 NA

Two-Component, Polyurethane Topcoat for Mapefloor Parking Deck System Mapefloor Finish 415 NA is a two-component, solvent-free, aromatic polyurethane topcoat specifically designed to provide a protective wear coat for elevated concrete surfaces where the Mapefloor parking deck system is utilized.

Microsilica

Densified Silica-Fume Admixture Microsilica is a densified powder admixture with pozzolanic action, to be used in combination with plasticizers and superplasticizers for high-quality mortars, grouts and concrete. Microsilica complies with the provisions and specifications of ASTM C1240 and AASHTO M307. Microsilica is an amorphous silicon dioxide (silica) consisting of sub-micron spherical primary particles and agglomerates of these. The material is highly reactive in cementitious and ceramic bond systems. The average diameter of a Microsilica sphere is about 0.15 micron. Although some of the spheres exist as single entities, most of them form primary agglomerates. The size of these may vary between 0.1 and 1 micron. This rather wide particle size distribution contributes to high packing efficiency.

Mapeshield CI 300

Corrosion-Inhibiting Admixture for Concrete Mapeshield CI 300 (formerly Polychem CI) is a liquid corrosion-inhibiting admixture based on calcium nitrite. Mapeshield CI 300 inhibits the onset of corrosion of reinforcing steel caused by chlorides typically present in de-icing materials. Mapeshield CI 300 meets or exceeds the requirement of ASTM C494, Type C; AASHTO M194, Type C; and ASTM C1582.

Planiseal WR 100

Clear, 100%-Silane, Penetrating Water Repellent Planiseal WR 100 is a clear, high-performance, 100%-silane, penetrating water repellent and sealer designed to provide water repellency on concrete and masonry. It penetrates deeply, protecting new and existing substrates against moisture/chloride intrusion.

Planiseal WR 40

Mapefloor Finish 450

Two-Component, Aliphatic, Polyurethane Topcoat Mapefloor Finish 450 is a two-component, solvent-free, aliphatic, polyurethane topcoat specifically designed to provide a protective wear coat for elevated concrete surfaces in areas that are exposed to direct sunlight.

Planiseal WR

Penetrating, Water-Based, Silane/Siloxane Water Repellent Planiseal WR is a silane/siloxane-blend, water-repellent, transparent sealer that provides resistance to water, dirt and chlorides.

Planibond 3C

Webinars, All Video Tutorials

MAPEI Webinar: LEED 101

Which version of LEED green building rating system should you use? And how should you best select and report…

All Video Tutorials, Webinars

MAPEI Webinar: ISO Certification More than a Stamp on a Package

What does the ISO stamp on a package mean and why should you look for it? Is it something that you should…

Webinars, All Video Tutorials

MAPEI Webinar: System Solutions for Healthcare Facilities

Bidding a flooring install in a healthcare facility? These projects demand a wide range of installations and…

All Video Tutorials, Webinars

MAPEI and Structures Webinar – Corrosion Mitigation of Traditionally Reinforced Concrete Structures

Methods and means to prevent corrosion of reinforcing steel

Mapefloor PU Primer [NA]

Mapefloor Finish 415 NA

Mapefloor PU 400 FC

+ 5

Show products

Featured Products

Mapefloor PU Primer [NA]

Two-Component Polyurethane Primer Mapefloor PU Primer [NA] is a two-component, polyurethane-based primer that can be used for initial application of Mapefloor parking deck systems or as a recoat primer for already installed polyurethane deck systems.

Mapefloor Finish 415 NA

Mapefloor PU 400 FC

Two-Component, Fast-Curing, Polyurethane Basecoat for Mapefloor Parking Deck System Mapefloor PU 400 FC is a two-component, fast-curing, polyurethane basecoat specifically designed for use as a waterproofing membrane for elevated concrete surfaces where the Mapefloor parking deck system is utilized. With its high elongation and crack-bridging properties, Mapefloor PU 400 FC is suited as a basecoat layer on concrete substrates subject to vibration.

Planiseal WR 100

Planiseal WR 40

Mapefloor Finish 450

Planiseal WR

Penetrating, Water-Based, Silane/Siloxane Water Repellent Planiseal WR is a silane/siloxane-blend, water-repellent, transparent sealer that provides resistance to water, dirt and chlorides.

Planibond 3C

All Video Tutorials, Webinars

MAPEI Webinar: How to Order Custom Mapeheat Mats

Want heated floors but room measurements leave you cold? Listen to this easy-to-follow Webinar and you are…

Mapeheat Mat

Show products

Featured Products

Mapeheat Mat

Pre-Wired, Floor-Heating Fabric Mapeheat Mat is a pre-wired floor-heating fabric designed for easy installation. The pre-wiring aspect of Mapeheat Mat guarantees even heat distribution because the heating wires embedded within the fabric are evenly spaced during production. A single standard-size mat can provide adequate floor-heat coverage for most standard bathroom and living areas. Installers can also combine multiple standard mats to heat the desired area. When full coverage cannot be achieved with standard-size mats (such as areas with curves, angles or obstructions), Mapeheat Mat can be customized to provide optimal coverage.

All Video Tutorials, Webinars

MAPEI Webinar: All About Green Squared

You see the logo on packaging and the Web, but what does G 2 , or “Green Squared,” mean? What industry…

MAPEI Flexcolor 3D

Ultraplan Lite

MAPEI Ultralite S2

+ 2

Show products

Featured Products

MAPEI Flexcolor 3D

Ultraplan Lite

MAPEI Ultralite S2

MAPEI Ultralite ® S2 is a premium-grade, lightweight, single-component thin-set mortar that is ideal for installation of gauged (formerly “thin”) porcelain tile. This high-performance, highly deformable, polymer-modified mortar is formulated with Easy Glide Technology ™ for ease of application. MAPEI Ultralite S2 features a long open time and superior transfer properties to enhance back-buttering, and can be used also for ceramic tile and stone. MAPEI Ultralite S2 ’s unique Ultralite Technology ™ provides twice the coverage of a standard thin-set mortar per pound/kg and may contribute to LEED points with 20% recycled content.

MAPEI Ultralite Mortar Pro

Professional, Lightweight Mortar with Polymer for Large and Heavy Tile MAPEI Ultralite Mortar Pro is a professional-grade, lightweight, single-component thin-set mortar that can also be used for large-and-heavy-tile and non-sag applications. This polymer-modified mortar is formulated with Easy Glide Technology for ease of application. MAPEI Ultralite Mortar Pro ’s unique Ultralite Technology provides twice the coverage of a standard thin-set mortar per pound/kg and contains more than 20% recycled content.

MAPEI Ultralite Mortar

MAPEI Ultralite ® Mortar is a premium-grade, lightweight, single-component mortar for large-and-heavy-tile and nonsag applications, and that can also be used for thin-set mortar installations. This high-performance, polymer- modified mortar features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions. It is formulated with Easy Glide Technology ™ for ease of application, and with BioBlock ® technology for mold and mildew resistance. MAPEI Ultralite Mortar utilizes Ultralite Technology ™ for twice the coverage of a standard thin-set mortar per pound/kg and contains more than 20% recycled content.

All Video Tutorials, Webinars

MAPEI Webinar: Tile Grout, Caulk, and Care and Maintenance Solutions

MAPEI offers a wide selection of grouts, caulks, and care and maintenance solutions. Choosing which to use,…

Mapesil T Plus

Ultracolor Plus Max

Kerapoxy

+ 8

Show products

Featured Products

Mapesil T Plus

Ultracolor Plus Max

Kerapoxy

MAPEI Flexcolor 3D

Kerapoxy IEG CQ

Keracaulk U

Premium, Unsanded Siliconized Acrylic Caulk Keracaulk U is a premium-grade, unsanded, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match all of MAPEI’s grout colors.

Keracaulk S

Premium, Sanded Siliconized Acrylic Caulk Keracaulk S is a premium-grade, sanded, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match all of MAPEI’s grout colors.

Keracolor S Sanded Grout

Keracolor U Unsanded Grout

MAPEI Flexcolor Design

Ultracolor Plus FA

All Video Tutorials, Webinars

MAPEI Webinar: The Science of Moisture-Related Failures and How They Can Be Prevented

Looking for concrete facts and not best guesses? What are the best methods for blocking moisture from…

Webinars

MAPEI Webinar: The Science of Floor Covering Adhesives and How They Relate to MAPEI Installation Products

With all of the flooring adhesives on the market, how do you decide which ones to use? Does it matter? Can…

Ultrabond ECO MS 4 LVT Wall [NA]

Ultrabond ECO MS 4 LVT [NA]

Ultrabond ECO 399

+ 20

Show products

Featured Products

Ultrabond ECO MS 4 LVT Wall [NA]

Ultrabond ECO MS 4 LVT [NA]

Ultrabond ECO 399

Ultrabond ECO 185

Ultrabond ECO 575 [NA]

Ultrabond ECO 350

Ultrabond ECO 977

Ultrabond ECO 907

Ultrabond ECO 373

Ultrabond ECO 983

Ultrabond ECO 985

Ultrabond ECO 995

Ultrabond ECO 20

Ultrabond ECO 980

Ultrabond ECO 975

Ultrabond ECO 220

Ultrabond ECO 360

Ultrabond G21

Ultrabond ECO 711

Ultrabond G19

Ultrabond ECO 570

Ultrabond ECO 901

Premium Adhesive for FRP Panels Ultrabond ECO 901 adhesive has been specfically formulated as a bonding agent for fiberglass reinforced plastic (FRP) panels.

Ultrabond ECO 811

Webinars

MAPEI Webinar: Sustainability 101

What is the most common environmental building program? Which one, if any, should you follow for your…

Webinars

MAPEI Webinar – Environmentally Friendly Solutions for Soil Conditioning

MAPEI’s Underground Technology Team introduces a more environmentally friendly soil conditioner that will…

Webinars

MAPEI Webinar – Underlayments for marine applications

MAPEI presents the flat-out facts about shipboard flooring installations and underlayments. How do these…

Mapedeck Flexiscreed

Mapedeck Ultrascreed

Mapedeck Epofloor

+ 12

Show products

Featured Products

Mapedeck Flexiscreed

Two-component, viscoelastic polyurethane base layer for levelling off internal and external decks on ships Mapedeck Flexiscreed is used to form a viscoelastic levelling layer before installing floor coverings on internal and external decks on ships.

Mapedeck Ultrascreed

Two-component, self-levelling, fillerized aliphatic polyurethane base layer for levelling off internal and external decks on ships Mapedeck Ultrascreed is used to level off internal and external bridge decks on ships before applying coating products or installing floor coverings.

Mapedeck Epofloor

Self-Leveling, Epoxy-Resin-Based Coating for Seamless Flooring Mapedeck Epofloor is a two-component, nonylphenol-free, colored, 100%-solids, self-leveling, self-extinguishing, epoxy-resin coating used to form a seamless floor on internal decks.

Mapedeck Litescreed

Mapedeck Litescreed Tixo

Lightweight, Thixotropic, Flexible Polyurethane-Based Screed Mapedeck Litescreed Tixo is a two-component, lightweight, thixotropic, polyurethane-resin-based screed compound to smooth and level metal surfaces – internal and external, vertical and horizontal – before the installation of finishes or tile.

Mapedeck Teak Design

Mapedeck Design

Mapedeck Finish 100

Mapedeck Primer 200

Bonding Agent for Polyurethane-Based Systems Mapedeck Primer 200 is a bonding agent that creates an adhesion-promoting layer between the substrate and polyurethane-based products and systems.

Mapecoat Guard 100

Mapedeck Eposcreed Lite

Ultraplan Marine 1400 [NA]

High-Strength, Lightweight, Fiber-Reinforced, Quick-Setting, Self-Leveling Underlayment Ultraplan Marine 1400 [NA] is a fiber-reinforced, high-strength, lightweight, quick-setting, self-leveling underlayment for smoothing and leveling interior ship decks, and is a component of a soundproof floating floor system. It can withstand light foot traffic after 3 hours and rubber-wheel traffic after 3 days. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT), Ultraplan Marine 1400 [NA] offers superior drying-out characteristics for quick curing and does not contribute to efflorescence.

Ultraplan Marine Fire [NA]

High-Performance, Quick-Setting, Fiber-Reinforced, Self-Leveling Underlayment Ultraplan Marine Fire [NA] is a self-leveling, quick-setting, fiber-reinforced underlayment for interior ship decks subject to heavy traffic, and is a component of a soundproof floating floor system. It has high compressive strength and can withstand light foot traffic after 3 hours and vehicular rubber-wheel traffic after 3 days. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT), Ultraplan Marine Fire [NA] offers superior drying-out characteristics for quick curing and does not contribute to efflorescence.

Ultraplan Marine 900 [NA]

Lightweight, Fiber-Reinforced, Quick-Setting, Self-Leveling Underlayment Ultraplan Marine 900 [NA] is a lightweight, fiber-reinforced, quick-setting, self-leveling underlayment for interior decks. It can withstand light foot traffic after 2 to 3 hours and rubber-wheel traffic after 3 days. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT), Ultraplan Marine 900 [NA] offers superior drying-out characteristics for quick curing and does not contribute to efflorescence.

Mapecem Marine 1000 [NA]

Pre-Blended, Lightweight, Shrinkage-Compensated, Cement-Based Screed Mortar Mapecem Marine 1000 [NA] is an accelerated-cure, lightweight, shrinkage-compensated screed mortar for leveling or sloping up to 2" (5 cm) thick for ship decks before installation of floor coverings or tiles. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT), Mapecem Marine 1000 [NA] offers superior drying-out characteristics for quick curing and does not contribute to efflorescence.

Webinars

MAPEI Webinar – MAPEI and NWFA – Work smarter, faster and more efficiently

As an industry, how do we recruit young talent? It certainly will not happen by continuing to do the same…

Webinars

MAPEI Webinar – Material Ingredient Reporting

That big bid requires material transparency. Don’t know how to fill out the paperwork? Learn how here.

Webinars

MAPEI Webinar – Combating High Moisture Conditions with MAPEI Patches

Damp or green concrete on the day of the flooring install? It’s okay – MAPEI has high-moisture-resistant…

Ultrabond ECO MS 4 LVT [NA]

Mapecontact SRT

Ultrabond ECO 399

+ 10

Show products

Featured Products

Ultrabond ECO MS 4 LVT [NA]

Mapecontact SRT

Ultrabond ECO 399

Ultrabond ECO 185

Mapecontact MRT

Ultrabond ECO 373

Ultrabond ECO 985

Ultrabond ECO 995

Ultrabond ECO 711

Mapecem Quickpatch

Planiprep PSC

Ultrabond ECO 811

Planiprep 4 LVT [NA]

High-Moisture-Resistant Skimcoat and Embossing Leveler Planiprep 4 LVT [NA] is a premixed, high-moisture-resistant, water-based, acrylic-resin-based skimcoat and embossing leveler.

Webinars

MAPEI and CTDA Webinar — TCNA and ANSI Specifying Successful Tile and Stone Systems by the Book

TCNA, ANSI and ISO standards – Do you know how to interpret the industry standards and handbooks? MAPEI’s Jim…

Webinars

MAPEI Webinar – MAP006B: Grouting for Success

Which grout is the right grout for your tile project? Listen to this MAPEI Webinar and get the expert tips to…

Kerapoxy CQ

Ultracolor Plus Max

MAPEI Flexcolor 3D

+ 5

Show products

Featured Products

Kerapoxy CQ

Premium, Epoxy Grout and Mortar with Color-Coated Quartz Kerapoxy CQ is a two-component, 100%-solids, epoxy grout and mortar that is nonsagging/nonslumping in joints up to 3/8" (10 mm) in width, water-cleanable and easy to apply. Kerapoxy CQ uses a proprietary aggregate to achieve its durable color, making it excellent for countertops, high-traffic areas, and areas needing stain and chemical resistance. Easy to maintain, Kerapoxy CQ will clean to the original color and contains BioBlock technology to help protect against mold and mildew. Kerapoxy CQ does not contribute to efflorescence and has excellent resistance to chemicals, staining, alkalinity, chlorine, cracking and color deterioration.

Ultracolor Plus Max

MAPEI Flexcolor 3D

Kerapoxy IEG CQ

Keracolor S Sanded Grout

Keracolor U Unsanded Grout

Ultracolor Plus FA

MAPEI Flexcolor CQ

MAPEI Flexcolor ® CQ is a professional-grade, ready-to-use specialty grout for precision commercial and residential installations with porcelain, ceramic and natural-stone tiles. MAPEI Flexcolor CQ can be used to grout interior/exterior tile, and its dense composition helps to prevent water-based stains by providing water repellency to the grout surface. MAPEI Flexcolor CQ is formulated with the latest innovation in quartz aggregate, which ensures color consistency, ease of cleanability and improved workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation of the low level of water in the formulation. Comparison testing of MAPEI Flexcolor CQ versus traditional Portland-cement grout has verifi ed that MAPEI Flexcolor CQ is 30% more cost-ef fi cient (based on typical rates of installers) and requires 65% less time to install.

Webinars

MAPEI Webinar – Grouting Tips for Extreme Temperature and Humidity Conditions

When the jobsite is too hot, too humid or too cold, grouting can be a real challenge. Fortunately, you don’t…

Kerapoxy CQ

Ultracolor Plus Max

MAPEI Flexcolor 3D

+ 6

Show products

Featured Products

Kerapoxy CQ

Ultracolor Plus Max

MAPEI Flexcolor 3D

Kerapoxy IEG CQ

Keracolor S Sanded Grout

Keracolor U Unsanded Grout

MAPEI Flexcolor Design

Ultracolor Plus FA

MAPEI Flexcolor CQ

Webinars

MAPEI Webinar – Puttin’ on the Ritz: A Facade-Restoration Systems Approach

South Beach’s historic Ritz-Carlton was fighting the normal beachside aging process when suddenly Hurricane…

Mapelastic Smart

Mapefer 1K [NA]

Elastocolor Primer AR

+ 2

Show products

Featured Products

Mapelastic Smart

Roller-Grade, Flexible, Cementitious, Intermediate Waterproofing Membrane for Concrete Protection Mapelastic Smart is a flexible, cementitious membrane for protecting new and repaired concrete structures. Mapelastic Smart is designed as an intermediate waterproofing membrane.

Mapefer 1K [NA]

Elastocolor Primer AR

Planitop 200

Water-Repellent Skimcoating Mortar for Concrete and Glass/Porcelain Mosaics Planitop 200 is a water-repellent skimcoating mortar designed to smooth, level and finish interior/exterior concrete walls and masonry, glass and porcelain mosaics, acrylic paints and drywall panels. Planitop 200 is a special blend of special binders and admixtures, selected aggregate and powder polymers, all formulated to produce high bond strength and easy finishing. Mixed only with water, Planitop 200 is available in gray and white.

Elastocolor Coat

Webinars

MAPEI Webinar – Waterproofing Decks and Balconies

When you think of decks and balconies, you think of gatherings and terrace plants or pools – not weight and…

Planiseal CR1

Mapedrain 35

Planiseal 288

+ 8

Show products

Featured Products

Planiseal CR1

Mapedrain 35

Planiseal 288

Flexible, Cementitious Waterproofing Mortar Planiseal 288 is a slightly flexible, two-component, polymer-modified, cementitious waterproofing and protective mortar for concrete and masonry.

Mapedrain TD Drainage Composite

High-Strength, High-Flow Drainage Composite for Foundations Mapedrain TD Drainage Composite is a high-strength, three-dimensional modular drainage and collection composite for foundations. It consists of a nonwoven filter fabric that is bonded to and wrapped around a molded polypropylene core, minimizing fabric intrusion into the drainage channels that can be caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core. Mapedrain TD Drainage Composite is designed to replace a conventional gravel-covered pipe drain.

Mapedrain TD Fittings

Fittings for Installing Mapedrain TD Drainage Composite Mapedrain TD Fittings consist of end outlet, side outlet, splice and corner fittings that are made out of polyethylene and assist in installing Mapedrain TD Drainage Composite . The end outlet fitting connects the end of Mapedrain TD Drainage Composite to a 4" (10 cm) corrugated pipe. The side outlet fitting connects the side of Mapedrain TD Drainage Composite to a 4" (10 cm) corrugated pipe. The splice fitting connects two pieces of Mapedrain TD Drainage Composite end to end. And the corner fitting connects two pieces of Mapedrain TD Drainage Composite together, at the inside or outside corners of a building.

Mapedrain 50

Extra High-Strength, High-Flow, Pre-Fabricated Drainage Composite Mapedrain 50 is an extra high-strength, three-dimensional drainage composite. It consists of a woven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core. Mapedrain 50 ’s woven, monofilament fabric withstands high abrasion from applied overburden and prevents intrusion into the drainage core due to its low elongation characteristics. As such, the woven fabric is better suited to receive direct poured concrete than nonwoven geotextile fabrics.

Mapedrain 30

High-Strength, High-Flow, Prefabricated Drainage Composite with Woven Filter Fabric Mapedrain 30 is a high-strength, three-dimensional drainage composite. It consists of a woven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core. Mapedrain 30 ’s woven, monofilament fabric withstands high abrasion from applied overburden and prevents intrusion into the drainage core due to its low elongation characteristics. As such, the woven fabric is better suited to receive direct poured concrete than nonwoven geotextile fabrics.

Mapedrain 40

High-Strength, Extra High-Flow, Prefabricated Drainage Composite Mapedrain 40 is a high-strength, three-dimensional drainage composite. It consists of a high-performance, heavyweight nonwoven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. Mapedrain 40 ’s 8-ounce (227-gram) nonwoven fabric provides superior filtration. This allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core.

Mapedrain 20

High-Strength, High-Flow, Prefabricated Drainage Composite Mapedrain 20 is a high-strength, three-dimensional drainage composite. It consists of a nonwoven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core.

Mapedrain 10

Moderate-Strength, Intermediate-Flow, Prefabricated Drainage Composite Mapedrain 10 is a moderate-strength, three-dimensional drainage composite. It consists of a nonwoven filter fabric bonded to individual dimples of a molded polypropylene core, minimizing fabric intrusion into the drainage channels caused by overburden pressure. The filter fabric allows water to pass freely into the drainage core, which provides hydrostatic relief while preventing the passage of soil or sand particles that might clog the core.

Planiseal 88

Webinars

MAPEI Webinar: MAP060: Selling Sustainability

LEED, Well Building, Living Building Challenge. These terms appear more frequently on project specifications…

Webinars

MAPEI Webinar: Dispensing Chemical Admixtures in Concrete

Sidewalks, patios, building foundations, roads — if something uses concrete, chances are that the concrete…

Mapefast Super Set II

Mapefast Super Set Plus

Mapecrete VMA

+ 11

Show products

Featured Products

Mapefast Super Set II

Non-Chloride Set-Accelerating Admixture Mapefast Super Set II (formerly known as Polychem Super Set II) is a non-chloride, accelerating and water-reducing admixture formulated to accelerate strength development and setting time of concrete in cold weather.

Mapefast Super Set Plus

Non-Chloride Accelerating Admixture Mapefast Super Set Plus (formerly known as Polychem Super Set Plus) is a non-chloride, water-reducing admixture formulated to accelerate the strength development and setting time of concrete in cold weather. Mapefast Super Set Plus can reduce labor costs associated with the finishing process. Because the non-corrosive Mapefast Super Set Plus will not aid in the corrosion of reinforcing steel embedded within the concrete, it is recommended for use in all types of concrete, especially reinforced and prestressed.

Mapecrete VMA

Viscosity-Modifying Admixture Mapecrete VMA (formerly Polychem VMA) is a liquid admixture specially formulated to improve the viscosity of highly flowable mixtures, decrease the potential for segregation and improve the finishing characteristics of lean concrete mixtures. Mapecrete VMA is recommended for use in self-consolidating concrete (SCC), concrete containing manufactured sand and high water-to-cement ratio mixes.

Mapeshield CI 300

Mapetard R

Set-Retarding Admixture for Concrete Mapetard R (formerly Polychem R) is a highly concentrated liquid admixture conforming to ASTM C494, Type D. Mapetard R reduces the quantity of mixing water required to produce concrete of a standard consistency with the benefit of extended slump life and workability. Concrete produced with Mapetard R will experience rapid strength development after the initial set occurs. If retardation is within the normal ASTM C494, Type B and D specifications, Mapetard R will develop higher early and ultimate strengths than regular concrete under normal comparable curing conditions.

Mapefast Super Set

Accelerating Admixture Mapefast Super Set (formerly known as Polychem Super Set) is a non-chloride, water-reducing admixture formulated to accelerate the strength development and setting time of concrete in cold weather. Mapefast Super Set can reduce labor costs associated with the finishing process. Mapefast Super Set is non-corrosive and, therefore, will not aid in the corrosion of reinforcing steel embedded within the concrete. It is recommended for use in all types of concrete, especially reinforced and prestressed.

Mapeplast Paver Plus

Water-Reducing Admixture Mapeplast Paver Plus (formerly known as Polychem Paver Plus) is a normal-setting, multi-component, highly concentrated water-reducing admixture. Mapeplast Paver Plus will reduce the quantity of water required to produce concrete of a desired consistency while providing greater economy for a given strength. It will increase strength and improve workability and finishing characteristics. Mapeplast Paver Plus does not contain calcium chloride, and is compatible with air-entrained and non-air-entrained mixes. Mapeplast Paver Plus was specifically designed for concrete slip-form paving operations to extend haul time and maintain workability.

Polychem Renu

Hydration-Stabilizing Admixture for Concrete Polychem Renu is a ready-to-use liquid solution manufactured to control the hydration process in Portland-cement concretes and concrete washwater. This advanced-set retarder coats the hydrating cement particles in the concrete and washwater, resulting in the suspension of the hydration chemical reaction. Polychem Renu maintains the plasticity, slump and temperature as it postpones the set of the concrete for a predictable period of time. Eventually, the Polychem Renu dosage is chemically consumed, allowing normal hydration to continue. Polychem Renu meets or exceeds the ASTM C494 and AASHTO M194 Type B and Type D requirements.

Mapefluid 441

High-Range, Water-Reducing Admixture Mapefluid 441 (formerly known as Polychem 441) is a water-soluble, naphthalene-based, high-range water-reducing admixture. Mapefluid 441 can reduce mixing water up to 30%, producing high-strength concrete with a low water/cement ratio that can be placed at normal levels of workability or can be added to a mix to produce flowing concrete with increased strength. Mapefluid 441 is chloride-free and non-corrosive. Mapefluid 441 is recommended for use in all concrete, especially reinforced/prestressed and post-tensioned concrete.

Mapefast HE

Water-Reducing, Accelerating Admixture Mapefast HE (formerly known as Polychem HE) is a chloride-based liquid admixture containing waterreducing and accelerating components. Mapefast HE can be used to accelerate the setting characteristics of concrete and promote early strength gain of concrete. Mapefast HE meets the requirements of ASTM C494 as a Type C and Type E, CRD C87 and AASHTO M194.

Vibromix BP

Plasticizing Admixture for Drycast Vibromix BP is a ready-to-use, high-performance, liquid plasticizer recommended for use in the production of standard and lightweight concrete blocks, pipes and any other manufactured concrete product, especially when zero or low slumps are required.

Mapeair VR

Air-Entraining Admixture Mapeair VR (formerly known as Polychem VR) is a ready-to-use air-entraining agent in an aqueous solution of neutralized vinsol resin. Mapeair VR meets or exceeds the requirements of ASTM C260, CRD 13 and AASHTO M154.

Mapeair SA

Air-Entraining Admixture Mapeair SA (formerly Polychem SA) is a specifically developed, multi-component air-entraining admixture that has been stabilized to produce an air-void system consistent with industry requirements and standards. When added separately, Mapeair SA will produce an air-void system that is equivalent to or exceeds that of pure Vinsol-resin-based admixtures at substantially reduced dosage rates. Mapeair SA is a synthetic-based alpha olefin that will produce a small, more well-defined and spaced bubble structure, which is stabilized to be more efficient when used in producing concrete mixtures containing low-alkali cement or supplementary cementitious materials. Mapeair SA conforms to the requirements of ASTM C260 and AASHTO M154.

Dynamon 850

Dynamon 850 (formerly Polychem 850) is a normal-setting, multi-range water-reducing admixture for concrete utilizing polycarboxylate technology. Dynamon 850 is designed to facilitate the placing and finishing of ready-mixed concrete that is highly flowable and workable for extended periods of time with normal-setting characteristics. Dynamon 850 meets or exceeds the requirements of ASTM C494 Type A and Type F, as well as AASHTO M194 Type A and Type F.

Webinars

MAPEI Webinar — Health and the Environment: Low-Emitting Materials

Green building standards and certification programs are increasingly important on jobsites, but what does all…

Webinars

MAPEI Webinar – MAP049A FRP Strengthening: Strengthening Concrete Structures with Fiber-Reinforced Polymers

Using fiber-reinforced polymers to strengthen concrete structures is an effective and efficient method of…

Webinars

MAPEI Webinar – An Introduction to MAPEI’s Marine Line

Set sail with MAPEI’s Products for the Marine Industry. From mortars and grouts to UV-protecting,…

Ultrabond Turf PU 2K

Ultraplan Marine 1400 [NA]

Ultraplan Marine Fire [NA]

+ 7

Show products

Featured Products

Ultrabond Turf PU 2K

Ultraplan Marine 1400 [NA]

Ultraplan Marine Fire [NA]

Ultraplan Marine 900 [NA]

Mapecem Marine 1000 [NA]

MAPEI Flexcolor 3D

Ultrabond ECO 360

Ultrabond G19

Granirapid System

Premium, Rapid-Setting, Flexible Tile Mortar Granirapid is the industry’s first and most flexible, high-performance, fast-curing mortar system geared for fast-track projects. It develops high, early mechanical strength and can be specified for the most demanding tile applications. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT), Granirapid offers superior drying-out characteristics for quick curing and does not contribute to efflorescence. When installed in conjunction with Ultracolor Plus FA grout, Granirapid will allow water submersion in only 72 hours.

Ultracolor Plus FA

Webinars

MAPEI Webinar – Protection on a Roll: MAPEI’s Sheet Membrane Systems

Whether it’s crack isolation, sound reduction, vapor management or waterproofing, MAPEI is the go-to source…

Mapetape BB

Mapeguard CI

Mapesound 90

+ 5

Show products

Featured Products

Mapetape BB

Butyl-Based, Sealing Tape for Use with MAPEI’s Bitumen-Based, Crack-Isolation Membranes Mapetape BB is a butyl-based, waterproofing sealing tape for use with MAPEI peel-and-stick, crack-isolation membranes. Mapetape BB has an extremely aggressive grip and superior long-term adhesion, ensuring immediate sealing upon contact. It is reverse-rolled for easy, fast application. A clear release liner on one side allows for easy handling and dry-fitting. Mapetape BB is compatible with Mapeguard 2 , Mapesonic 2 , Mapesound 90 and Mapeguard CI membranes.

Mapeguard CI

Peel-and-Stick, Crack-Isolation Sheet Membrane for Tile Installations Mapeguard CI is a flexible, thin (1/16" or 1.5 mm), lightweight, load-bearing, fabric-reinforced, “peel-and-stick” crack-isolation membrane. After application, ceramic tile or stone can be installed immediately with approved polymer-modified cement-based mortar. Mapeguard CI helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" or 10 mm wide) from transmitting through grout, ceramic tile or natural stone.

Mapesound 90

Professional, Sound-Reduction and Crack-Isolation Sheet Membrane Mapesound 90 is a flexible, thin, 90-mil, lightweight, load-bearing, fabric-reinforced “peel-and-stick” sound-reduction and crack-isolation membrane. After application, ceramic tile or stone can be installed immediately with a recommended MAPEI polymer-modified cement-based mortar, or glue-down wood flooring can be immediately installed with any MAPEI urethane or hybrid-polymer-based wood adhesive. Mapesound 90 reduces transmission of impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) through floors when installed under ceramic tile, stone or wood floor coverings. It also helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" [10 mm] wide) from transmitting through grout, ceramic tile or natural-stone assemblies.

MAPEI SM Primer Fast

Fast-Tacking, Water-Based Primer for MAPEI Peel-and-Stick Membranes MAPEI SM Primer Fast is a ready-to-use, fast-drying, quick-tacking, water-based, pressure-sensitive, nonhydrolyzable latex primer for use under MAPEI’s peel-and-stick sheet membranes on residential and commercial indoor or outdoor floors. MAPEI SM Primer Fast greatly increases the bond of MAPEI’s peel-and-stick sheet membranes to concrete, plywood and other approved, properly prepared floors. It can be applied with a roller or brush, is white in color and dries clear.

Mapesonic 2

All-in-One Membrane for Crack Isolation, Sound Reduction, Waterproofing and Vapor Management Mapesonic 2 is a patented, next-generation, flexible, 76-mil thin, lightweight, load-bearing, fabric-reinforced, “peel-and-stick” membrane for sound reduction, crack isolation, waterproofing and vapor management. Application of Mapesonic 2 can be immediately followed by installation of finished flooring. Mapesonic 2 reduces transmission of impact sound (such as footsteps and dropped objects) and airborne sound (such as voice and TV) through floors when installed under ceramic tile, stone, vinyl and wood floorings. It also helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" or 10 mm wide) from transmitting through grout, ceramic tile and natural-stone assemblies.

Mapeguard 2

3-in-1 Membrane for Crack Isolation, Waterproofing and Sound Reduction Mapeguard 2 is a next-generation, flexible, thin, 40-mil (1-mm) lightweight, load-bearing, fabric-reinforced “peel-and-stick” crack-isolation, waterproofing and vapor-control membrane. Mapeguard 2 helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" [10 mm] wide) from transmitting through grout, ceramic tile and natural stone. It also reduces the transmission of impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) through floors when installed under ceramic tile, stone or wood floor coverings.

MAPEI SM Primer

MAPEI SM Primer ™ is a ready-to-use, fast-drying, water-based, latex primer for use under MAPEI’s peel-and-stick sheet membranes on residential and commercial indoor or outdoor floors. MAPEI SM Primer greatly increases the bond of MAPEI’s peel-and-stick sheet membranes to concrete, plywood and other approved, properly prepared floors. It can be applied with a roller or brush, is white in color and dries clear.

MAPEI HM Primer

Water-Based, Interior/Exterior Primer for Sheet Membranes MAPEI HM Primer is a ready-to-use, low-VOC, water-based, quick-drying, high-tack membrane primer. It is specifically formulated to promote maximum adhesion of MAPEI peel-and-stick sheet membranes to high-moisture substrates.

Webinars

MAPEI Webinar – Strengthening of Bridges with the MapeWrap Fiber-Reinforced Polymer (FRP) System

Whether used to increase the load-bearing capacity of a structure, or to restore loss of capacity from damage…

MapeWrap 31

MapeWrap 21

MapeWrap Primer 1

+ 2

Show products

Featured Products

MapeWrap 31

MapeWrap 21

MapeWrap Primer 1

MapeWrap 11

MapeWrap 12

Webinars

MAPEI Webinar – Mortar Selection Simplified: Keraflex Technology to the Rescue!

Learn how Keraflex polymer-modified mortar technology not only revolutionizes the large-and-heavy-tile…

Keraflex RS

Keraflex SG

Keraflex Super

+ 1

Show products

Featured Products

Keraflex RS

Keraflex SG

Standard, Extra Smooth, Large-and-Heavy-Tile Mortar with Polymer Keraflex SG is a standard-grade, versatile, large-and-heavy-tile mortar and thin-set mortar for tile and stone installations on floors, walls and countertops. It is formulated as nonsag for walls and nonslump for floors. Keraflex SG is a polymer-modified mortar formulated with Easy Glide Technology for ease of application and offers good adhesion to substrates and tile. It can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.

Keraflex Super

Keraflex Plus

Webinars

MAPEI Webinar – MAP047A: ANSI A118.15 Improved Modified Dry-Set Mortar, LHT, and ANSI Mortar Designations

Heard about the new ANSI mortar designation for LHT mortars? Do you know how it will affect your jobsites and…

Ultraflex LHT

Ultraflex LFT

Ultraflex LHT SG

Show products

Featured Products

Ultraflex LHT

Professional Large-and-Heavy-Tile Mortar with Polymer Ultraflex LHT is a non-sag, large-and-heavy-tile mortar and thin-set mortar for large-format and heavy tile and stone for interior/exterior installations on floors, walls and countertops. Ultraflex LHT is designed for use at 1/2" (12 mm) thickness to give better support under large-format tile. This polymer-modified mortar is formulated with Easy Glide Technology for ease of application with excellent adhesion to the substrate and tile.

Ultraflex LFT

Ultraflex ® LFT ™ is a premium, nonsag, large-and-heavy-tile mortar and thin-set mortar designed for large-format and heavy tile and stone for interior/exterior floor, wall and countertop installations. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. This product features a very low emission of volatile organic compounds and includes an offset of greenhouse gas emissions. It is formulated with Easy Glide Technology ™ for ease of application.

Ultraflex LHT SG

Standard, Large-and-Heavy-Tile Mortar with Polymer Ultraflex LHT SG is a standard-grade, nonsag, nonslump, polymer-modified, large-and-heavy-tile mortar and thin-set mortar for interior/exterior installations on floors, walls and countertops. It is used to install large-format and heavy tile/stone, including porcelain tile, heavy-ribbed-back tile, brick pavers, dimensional tile and natural-stone tile. Ultraflex LHT SG is designed for use at 3/32" to 1/2" (2.5 to 12 mm) thickness to give better support under large-format tile. This mortar is formulated with Easy Glide Technology for ease of application and good adhesion to the substrate and tile.

Webinars

MAPEI Webinar – MAPEI UTT Waterproofing & Injection Grout Solutions for Tunneling and Underground

MAPEI’s Underground Technology Team offers specialized waterproofing and injection grout solutions customized…

Webinars

MAPEI Webinar – Advances in Wood-Flooring Installation Options

Which moisture-control products work best with MAPEI’s wood adhesives? How do you select the right primer for…

Ultrabond ECO 977

Ultrabond ECO 907

Mapesonic RM

+ 13

Show products

Featured Products

Ultrabond ECO 977

Ultrabond ECO 907

Mapesonic RM

Planiseal MSP

Ultraplan Extreme 2

Ultrabond ECO 983

Planiseal VS Fast

Ultrabond ECO 985

Ultrabond ECO 995

Planiseal VS

Ultrabond ECO 980

Ultrabond ECO 975

Ultrabond Urethane Cleaner

Mapecem Quickpatch

Planipatch

Planiprep SC

Webinars

MAPEI Webinar – Advances in Primary Below-Grade Waterproofing

Are you positively confused about positive- and negative-side waterproofing? Get answers here in this…

Planiseal CR1

Planiseal 288

Planiseal 88

Show products

Featured Products

Planiseal CR1

Planiseal 288

Flexible, Cementitious Waterproofing Mortar Planiseal 288 is a slightly flexible, two-component, polymer-modified, cementitious waterproofing and protective mortar for concrete and masonry.

Planiseal 88

Webinars

MAPEI Webinar – Best Practices for Synthetic Turf Adhesives

Whether you are installing turf indoors or out, in hot or cold weather, MAPEI offers a variety of…

Ultrabond Turf PU 2K

Ultrabond Landscape Turf CG

Ultrabond Landscape Tape

+ 5

Show products

Featured Products

Ultrabond Turf PU 2K

Ultrabond Landscape Turf CG

Ultrabond Landscape Tape

Ultrabond Turf PU 1K-LV

Ultrabond Turf PU 2K Accelerator

Ultrabond Turf Tape

Ultrabond Turf PU 1K-HV

Ultrabond Turf PU 1K

Webinars

MAPEI Webinar – Navigating Self-Leveler and Primer Options

Why do you have to use primer with self-leveling compounds? Why are there so many primers and self-levelers?…

Novoplan HFL

Novoplan DPL

Ultraplan Extreme 2

+ 10

Show products

Featured Products

Novoplan HFL

Novoplan DPL

Ultraplan Extreme 2

Ultraplan Lite

Novoplan Easy Plus

Novoplan 2 Plus

Professional, Self-Leveling Underlayment Novoplan 2 Plus is a high-strength, self-leveling, cement-based underlayment and repair mix for interior concrete and engineer-approved floors.

Ultraplan M20 Plus

Ultraplan Easy

Primer T

Primer L

Ultraplan 1 Plus

ECO Prim Grip

Primer X

Webinars

MAPEI Webinar – An Introduction to UTT and Tunnel Boring Machines

Tunneling and mining are just two of the many solutions provided by MAPEI’s Underground Technology Team…

Webinars

MAPEI Webinar – Elastocolor Coatings: High-Performance Protection and Durable Color Design

How does a coating prevent corrosion? Is truly unlimited color-matching possible? Find out here.

Elastocolor Flex

Elastocolor Primer AR

Elastocolor Coat

+ 3

Show products

Featured Products

Elastocolor Flex

Elastocolor Primer AR

Elastocolor Coat

Elastocolor Primer WB

Elastocolor Paint

Elastocolor Texture

Webinars, MTI-TV

MTI Online: Mapeheat Pro Installer Registration Training (prerecorded)

Designed for those interested in the Mapeheat system, this training session will provide an overview of all…

Mapeheat Mat

Mapeheat Cable

Show products

Featured Products

Mapeheat Mat

Mapeheat Cable

Radiant-Heating Cable for Use with Mapeheat Membrane Mapeheat Cable is a free-form, twisted-pair, floor-heating cable for use in any residential interior room where the comfort of radiant floor heating is desired. The cable can be spaced on site to provide 10, 12 or 15 W per sq. ft. based on the desired wattage output requirements of the installation. Mapeheat Cable is available in 33 lengths to accommodate areas as small as 6 sq. ft. (0.56 m²) and up to 293 sq. ft. (27.2 m²).

Webinars

MAPEI Webinar: Best Practices for Ceramic Tile and Stone – Efflorescence and Latex Migration

Are white streaks running from your grout joints? You may have efflorescence or latex migration.

UltraCare Penetrating SB Stone, Tile & Grout Sealer

UltraCare Sulfamic Acid Crystals

UltraCare Heavy-Duty Sealer & Coating Stripper

+ 3

Show products

Featured Products

UltraCare Penetrating SB Stone, Tile & Grout Sealer

UltraCare Sulfamic Acid Crystals

UltraCare Sulfamic Acid Crystals is a granular powder that dissolves in water and produces a cleaner and problem-solver for nonporous, acid-resistant tile and natural stone. It removes cured cement grout haze, mortar residue, rust stains and mineral deposits such as efflorescence.

UltraCare Heavy-Duty Sealer & Coating Stripper

UltraCare Heavy-Duty Sealer & Coating Stripper is a professional-strength formulation that helps to remove tough coatings, lacquers, varnishes, sealers, paints and epoxy grout haze from surfaces. This product effectively dissolves heavy wax, and helps to remove deep-set stains and heavy grease buildup. UltraCare Heavy-Duty Sealer & Coating Stripper is water-based, pleasantly scented, nonflammable and easy to use.

UltraCare Abrasive Surface Cleaner

UltraCare Abrasive Surface Cleaner is a powerful, abrasive cleaner that is safe for use on a variety of ceramic, porcelain and natural-stone surfaces. This water-based, biodegradeable formula is nontoxic and nonflammable, containing no VOCs or acids. Cleaning does not require letting the product stand on the surface. UltraCare Abrasive Surface Cleaner penetrates deep into dense surface pores and easily removes ground-in dirt, grime, rust stains and mineral deposits. This product is formulated to remove most factory-applied waxes and floor finishes as well as light cementitious and epoxy grout residue. It is excellent for use on heavily textured and hard-to-clean surfaces. Plus, it can be used in combination with any UltraCare cleaner or problem-solver.

UltraCare Penetrating Plus Stone, Tile & Grout Sealer

UltraCare Heavy-Duty Stone, Tile & Grout Cleaner

UltraCare Heavy-Duty Stone, Tile & Grout Cleaner is a highly concentrated and high-alkaline cleaner and degreaser. This product is formulated to quickly remove most waxes, grease, oil, light soap scum, and stains from mildew and algae. It is quite effective at removing most factory-applied waxes and floor finishes, and is ideal for areas that have been neglected or subject to heavy use.

Webinars

MAPEI Webinar – Installing epoxy grout in a commercial kitchen

Epoxy grout is the most durable, stain-resistant grout. It can withstand harsh chemicals and heavy traffic,…

Ultracolor Plus Max

MAPEI Flexcolor 3D

Kerapoxy IEG CQ

Show products

Featured Products

Ultracolor Plus Max

MAPEI Flexcolor 3D

Kerapoxy IEG CQ

Webinars

MAPEI Webinar: Systems and Solutions for Gauged Porcelain Tile Panels and Slabs

The ANSI A108.19 standard for the installation of gauged porcelain tile panels and slabs can change the way…

Keraflex Super

MAPEI Ultralite S2

Ultraflex LFT

+ 5

Show products

Featured Products

Keraflex Super

MAPEI Ultralite S2

Ultraflex LFT

4 to 1 Mud Bed Mix

Sand and Cement Mortar Mix 4 to 1 is a pre-blended mixture of finely graded sand and Portland cement used for thick-bed mortar installations. 4 to 1 flattens and levels an existing substrate before the installation of tile and stone.

Mapecem Quickpatch

Modified Mortar Bed

Polymer-Modified Thick-Bed and Render Mortar Modified Mortar Bed is a pre-blended, cement-based, polymer-modified thick-bed and render mortar that includes a blend of selected aggregates. Rather than requiring the use of a latex additive, it only needs mixing with water to produce a thick bed mortar of exceptional strength.

Planitop 330 Fast

Quick-Setting, Fiber-Reinforced, Cementitious Rendering Mortar Planitop 330 Fast is a quick-setting, polymer-modified, fiber-reinforced cementitious rendering, patching and leveling mortar for interior and exterior walls, floors and submerged areas. It can be applied from 1/8" to 1-1/4" (3 mm to 3.2 cm) in thickness to ramp, smooth and level surfaces. Eliminating the need for a latex additive, Planitop 330 Fast requires only mixing with water to produce a non-sagging mortar that is ready for tile installation in as little as 90 minutes.

Ultrabond ECO GPT

Hybrid-Polymer-Based Adhesive for Gauged Porcelain Tile Ultrabond ECO GPT is a single-component, nonsag, easy-to-trowel, hybrid-polymer-based adhesive technology specially designed for the installation of gauged porcelain tile and gauged porcelain tile panels/slabs on interior/exterior vertical surfaces and countertops. Unique technology advancements are incorporated in the formulation of Ultrabond ECO GPT for delivering instant grab, while allowing for the needed adjustability of panels and large-format tile. Superior bonding performance is complemented with flexibility, deformability and quick-curing characteristics to meet the demands of installing gauged porcelain tile, panels and slabs with application-friendly properties.

Webinars

MAPEI Webinar – Installing LVT Systems in Wet Environments

MAPEI’s Shower System for LVT allows for more creative decor and increases the speed of shower installations.…

Webinars

MAPEI Webinar – Selecting and Specifying Ceramic Tile with ANSI and ISO Standards

How do ANSI and ISO standards affect jobsites and specifications? Learn how today’s hottest tile trends –…

Keraflex Super

Kerabond T / Keralastic System

Ultraflex LFT

+ 3

Show products

Featured Products

Keraflex Super

Kerabond T / Keralastic System

Premium, Flexible Large-and-Heavy-Tile and Thin-Set Mortar Kerabond T / Keralastic System is a high-performance, two-part system: Keralastic , a second-generation “flexible” acrylic latex additive, is used to enhance the performance of Kerabond T , which is a premium-grade, large-and-heavy-tile mortar and thin-set mortar. This system has exceptional bond strength, flexural strength, elongation and freeze/thaw durability.

Ultraflex LFT

Granirapid System

Kerabond/Keralastic System

Premium, Flexible Tile Mortar Kerabond/Keralastic System is a high-performance, two-part system: Keralastic , a second-generation “flexible” acrylic latex additive, is used to enhance the performance of Kerabond , which is a premium-grade dry-set mortar. This system has exceptional bond strength, flexural strength, elongation and freeze/thaw durability. To ensure proper flexibility, always use a latex additive when applying a dry-set mortar over plywood or difficult-to-bond tiles.

Ultrabond ECO GPT

Webinars

MAPEI NWFA Webinar – The Shortest Distance Between Two Points – NWFA Sam Biondo, 2020

Installing a wood floor? Not all wood floors are the same and neither are surface-prep techniques. Sam Biondo…

Ultraplan Extreme 2

Ultraplan Lite

Novoplan 2 Plus

+ 2

Show products

Featured Products

Ultraplan Extreme 2

Ultraplan Lite

Novoplan 2 Plus

Professional, Self-Leveling Underlayment Novoplan 2 Plus is a high-strength, self-leveling, cement-based underlayment and repair mix for interior concrete and engineer-approved floors.

Ultraplan M20 Plus

Ultraplan 1 Plus

Webinars

Webinar: Poor Substrate Conditions, Environmental Conditions, Best Practices

Learn about fixing substrate problems with MAPEI’s solutions, which include mortars, skimcoats, self-leveling…

Ultraplan Extreme 2

Ultraplan Lite

Novoplan 2 Plus

+ 6

Show products

Featured Products

Ultraplan Extreme 2

Ultraplan Lite

Novoplan 2 Plus

Professional, Self-Leveling Underlayment Novoplan 2 Plus is a high-strength, self-leveling, cement-based underlayment and repair mix for interior concrete and engineer-approved floors.